DeWalt DWE4056 Скачать руководство пользователя

Страница: 45 / 216

english

Mounting Wire Brushes

and Wire Wheels

Wire cup brushes or wire wheels screw directly

on the grinder spindle without the use of flanges.

Use only wire brushes or wheels provided with a

M14 threaded hub. A Type 27 guard is required

when using wire brushes and wheels.

CAUTION: Wear work gloves when

handling wire brushes and wheels.

They can become sharp.

CAUTION:

Wheel or brush must not

touch guard when mounted or while

in use. Undetectable damage could

occur to the accessory, causing wires to

fragment from accessory wheel or cup.

1. Thread the wheel on the spindle by hand.
2. Depress spindle lock button and use a wrench

on the hub of the wire wheel or brush to tighten

the wheel.

3. To remove the wheel, reverse the

above procedure.

NOTICE:

Failure to properly seat the

wheel hub before turning the tool on may

result in damage to tool or wheel.

Fitting and Removing a

Backing Pad/Sanding Sheet (fig. 1)

1. Place the tool on a table or flat surface, with the

guard facing up.

2. Remove the backing flange (D).
3. Place the rubber backing pad correctly onto the

spindle (B).

4. Place the sanding sheet on the rubber backing

pad.

5. Screw the threaded clamp nut (E) onto the

spindle. The ring on the threaded clamp nut

must face towards the rubber backing pad.

6. Press the spindle lock button (A) and rotate the

spindle (B) until it locks in position.

7. Tighten the threaded clamp nut (E) with the hex

key provided or a two pin spanner.

8. Release the spindle lock.
9. To remove the rubber backing pad, loosen

the threaded clamp nut (E) with the hex key

provided or a two pin spanner.

Fitting a Wire Cup Brush

Screw the wire cup brush directly onto the spindle

without the use of the spacer and threaded flange.

NOTE:

If, after a period of time the closed (Type 1)

guard becomes loose, tighten the adjusting screw

with the clamp lever in the closed position.

CAUTION:

If the guard cannot be

tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to authorized repair agent to repair or
replace the guard.

NOTICE:

Do not tighten adjusting

screw with clamp lever in open position.

Undetectable damage to guard or

mounting hub may result.

Fitting and Removing a Grinding or

Cutting Disc (fig. 1, 4, 5)

WARNING:

Do not use a damaged

disc.

1. Place the tool on a table, guard up.
2. Fit the backing flange (D) correctly onto the

spindle (B) (fig. 4).

3. Place the disc (P) on the backing flange (D).

When fitting a disc with a raised centre, make

sure that the raised centre (O) is facing the

backing flange (D).

4. Screw the threaded clamp nut (E) onto the

spindle (B) (fig. 5):

a. The ring on the threaded clamp nut (E) must

face towards the disc when fitting a grinding

disc (fig. 5A);

b. The ring on the threaded clamp nut (E)

must face away from the disc when fitting a

cutting disc (fig. 5B).

5. Press the spindle lock button (A) and rotate the

spindle (B) until it locks in position.

6. Tighten the threaded clamp nut (E) with the hex

key provided or a two pin spanner.

7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp

nut (E) with the hex key provided or a two pin

spanner.

NOTE:

Edge grinding can be performed with

Type 27 wheels designed and specified for this
purpose; 6 mm thick wheels are designed for
surface grinding while 3 mm wheels are designed
for edge grinding. Cutting can be performed by
using a cutting wheel and a Type 1 guard.