DeWalt DW715-XE Скачать руководство пользователя страница 15

Страница: 15 / 16

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE!

SAW WILL NOT START

WHAT’S WRONG?

WHAT TO DO…

1. Saw not plugged in

1. Plug in saw.

2. Fuse blown or circuit breaker tripped

2. Replace fuse or reset circuit breaker

3. Cord damaged

3. Have cord replaced by authorized service center

4. Brushes worn out

4. Have brushes replaced by authorized service center or replace them

yourself as instructed on page 7.

TROUBLE!

SAW MAKES UNSATISFACTORY CUTS

WHAT’S WRONG?

WHAT TO DO…

1. Dull blade

1. Replace blade. See pages 5, 6.

2. Blade mounted backwards

2. Turn blade around. See page 6.

3. Gum or pitch on blade

3. Remove blade and clean with turpentine and coarse steel wool or

household oven cleaner.

4. Incorrect blade for work being done

4. Change the blade type. See page 3.

TROUBLE!

BLADE DOES NOT COME UP TO SPEED

WHAT’S WRONG?

WHAT TO DO…

1. Extension cord too light or too long

1. Replace with adequate size cord. See page 2.

2. Low house voltage

2. Contact your electric company.

TROUBLE!

MACHINE VIBRATES EXCESSIVELY

WHAT’S WRONG?

WHAT TO DO…

1. Saw not mounted securely to stand or work bench

1. Tighten all mounting hardware. See page 4.

2. Stand or bench on uneven floor

2. Reposition on flat level surface. See page 4.

3. Damaged saw blade

3. Replace blade. See pages 5, 6.

TROUBLE!

DOES NOT MAKE ACCURATE MITER CUTS

WHAT’S WRONG?

WHAT TO DO…

1. Miter scale not adjusted correctly

1. Check and adjust. See page 6.

2. Miter pointer not adjusted correctly

2. Check and adjust. See page 6.

3. Workpiece is not perpendicular to table

3. Check and adjust fence. See page 6.

4. Workpiece moving

4. Clamp workpiece to fence or glue 120 grit sandpaper

to fence with rubber cement.

TROUBLE!

MATERIAL PINCHES BLADE

WHAT’S WRONG?

WHAT TO DO…

1. Cutting bowed material

1. Position bowed material as shown on page 12.

Содержание DW715-XE

















Результаты поиска

Содержание DW715-XE

Отзывы:

Похожие инструкции для DW715-XE

Бренды по названию

Популярные бренды

DeWalt DW715-XE, Инструкция по эксплуатации

Результаты поиска

Содержание DW715-XE

Отзывы:

Похожие инструкции для DW715-XE

Бренды по названию

Популярные бренды