ENGLISH
28
1.
Adjust the depth of cut as described above.
2. Set the fine adjuster to zero using the ring (x).
3. Rotate the fine adjuster (q) to the required
position: one turn corresponds to approximately
1 mm and 1 mark to 0.1 mm.
Depth Adjustment with Router
INSTALLED IN INVERTED POSITION (FIG. 4)
1. Remove the depth stop (m) and replace it with
the depth stop (DE6956) available as an option.
2. Connect the threaded rod of the depth stop (m)
to the revolver depth stop (l).
3. Set the depth of cut using the adjuster on the
depth stop (m).
WARNING:
For installing the router in
inverted position, refer to the relevant
instruction manual on the stationary tool.
Fitting the Parallel Fence (fi g. 1, 5)
1. Fit the guide rods (e) to the router base (j).
2. Tighten the locking bolts (i).
3. Slide the parallel fence (h) over the rods.
4. Tighten the locking bolts (d) temporarily.
5. Remove the dust extraction adaptor (r) and
close the outlet using the dust extraction plug
(y) supplied with the tool.
Adjusting the Parallel Fence (fi g. 6)
1. Draw a cutting line on the material.
2.
Lower the router carriage until the cutter is in
contact with the workpiece.
3.
Tighten the plunge limiter (o).
4. Position the router on the cutting line.
5. Slide the parallel fence (h) against the workpiece
and tighten the locking bolts (d).
6. Adjust the parallel fence (h) using the fine
adjuster (g). The outer cutting edge of the cutter
must coincide with the cutting line.
7. Firmly tighten the end lock (t).
Fitting a Guide Bush (fi g. 7)
Together with a template, guide bushes play a
valuable part in cutting and shaping to a pattern.
–
Fit the guide bush (z) to the router base (j) using
the screws (aa) as shown.
Connecting a Dust Extractor
(fi g. 1, 5)
Connect a dust extractor hose to the dust extraction
adaptor (r) in the router carriage column or to the
dust extraction outlet in the parallel fence (f).
Prior to Operation
1. Check that the cutter is correctly installed in
the collet.
2. Select the optimal speed using the electronic
speed control dial.
3. Set the cutting depth.
4. Connect a dust extractor.
5. Make sure the plunge limiter is always locked
before switching on.
OPERATION
Instructions for Use
WARNING:
Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories.
WARNING:
Always move your router as
indicated in figure 8 (outer edges/inner
edges).
Proper Hand Position (fi g. 11)
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
use
proper hand position as shown.
WARNING:
To reduce the risk of
serious personal injury,
ALWAYS
hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on either
plunge limiter (o).
Switching On and Off (fi g. 9)
The lock-on/lock-off switch (a) is located in the
handle on the right-hand side. The router is normally
locked in the off position.
Содержание DW621
Страница 1: ...DW621 DW622 www eu ...
Страница 3: ...1 Figure 1 xxxx xx xx a b c d e f g h i j k l m n o p q r s t Figure 2 Figure 3 b c dd c u ff ...
Страница 4: ...2 Figure 4 o n m l q x v p w p l m r y i j h f e t d g o h t d g Figure 5 Figure 6 ...
Страница 5: ...3 Figure 9 Figure 11 Figure 10 Figure 7 Figure 8 a bb cc j z aa ee j o o ...
