DeWalt DHS790 страница 23 Скачать руководство пользователя

Страница: 23 / 24

English

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

TROUBLE!

WHAT’S WRONG?

WHAT TO DO

Saw will not start

1. Battery or power supply not installed

1. Install battery or power supply. Refer to

Installing and Removing the Battery Packs

Installing and Removing D

WALT Corded Power Supply.

2. Battery or power supply not fully inserted 2. Check that battery or power supply are fully latched. Check AC adapter plug in the motor housing

for debris. Refer to

WALT Corded Power Supply Cleaning Instructions.

3. Batteries not charged

3. Charge batteries. Refer to

Charging Procedure.

4. Power supply not plugged in

4. Plug in saw.

5. Cord damaged

5. Have cord replaced by authorized service center.

6. Fuse blown or breaker tripped

6. Replace fuse or reset circuit breaker.

7. Saw overheated

7. Wait several minutes for saw to cool.

8. Batteries overheated

8. Wait several minutes for batteries to cool.

Saw makes

unsatisfactory cuts

1. Dull blade

1. Replace blade. Refer to

Changing or Installing a New Saw Blade.

2. Blade mounted backwards

2. Turn blade around. Refer to

Changing or Installing a New Saw Blade.

3. Gum or pitch on blade

3. Remove blade and clean with turpentine and coarse steel wool or household oven cleaner.

4. Incorrect blade for work being done

4. Change the blade type. Refer to

Saw Blades

under

Accessories.

Blade does not come up

to speed

1. Extension cord too light or too long

1. Replace with adequate size cord. Refer to

Use Proper Extension Cord

under

Important Safety

Instructions.

2. Low house current

2. Contact your electric company.

Machine vibrates excessively

1. Saw not mounted securely to stand or

work bench

1. Tighten all mounting hardware. Refer to

Bench Mounting.

2. Stand or bench on uneven floor

2. Reposition on flat level surface. Refer to

Familiarization.

3. Damaged saw blade

3. Replace blade. Refer to

Changing or Installing a New Saw Blade.

Does not make accurate

miter cuts

1. Miter scale not adjusted correctly

1. Check and adjust. Refer to

Miter Scale Adjustment

under

Adjustments.

2. Miter pointer not adjusted correctly

2. Check and adjust. Refer to

Miter Pointer Adjustment

under

Adjustments.

3. Workpiece is not perpendicular to table

3. Check and adjust fence. Refer to

Fence Adjustment

under

Adjustments.

4. Workpiece moving

4. Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement.

Material pinches blade

1. Cutting bowed material

1. Refer to

Bowed Material

under

Special Cuts.

CUTLINE

™

worklight flashing

1. Battery low on charge

1. Charge batteries. Refer to

Charging the Battery.

2. Battery hot

2. Wait several minutes for batteries to cool.

Содержание DHS790

























Результаты поиска

Содержание DHS790

Отзывы:

Похожие инструкции для DHS790

Бренды по названию

Популярные бренды

DeWalt DHS790, Инструкция по эксплуатации

Результаты поиска

Содержание DHS790

Отзывы:

Похожие инструкции для DHS790

Бренды по названию

Популярные бренды