ENGLISH
18
WARNING:
For your own safety,
read and understand the
mitre saw
instruction manual before using. Failure
to heed these warnings may result in
personal injury and serious damage to
the mitre saw and the accessory.
NOTE:
If you do not have a D
E
WALT mitre saw, you
must use 19 mm plywood to mount your mitre saw.
The plywood must be a minimum of 101.6 mm
wider than the the largest width of the mitre saw
base. The plywood should be at least as deep
as the smallest depth of the mitre saw base or a
minimum of 406.4 mm if mitre saw base is smaller.
Ensure the plywood is square.
1. Once the plywood size has been determined,
drill 9.5 mm holes 25.5 mm from the front
corners of plywood, 355 mm apart and
25.5 mm from the sides.
2. Place DE7025 mounting brackets onto the
stand:
a.
Grasp and squeeze release levers (b).
b.
Engage the concave front lip of the mounting
bracket with rounded front edge of beam.
One of the mounting brackets must be
engaged in the locator clip (d) to prohibit
lateral movement of the saw during use.
3. When the front edge of the beam and locator
clip are engaged, a slight downward pivot
will allow secure engagement of the release
levers to the back of the beam. Follow same
procedure with second mounting bracket at the
appropriate position on the beam for the size of
the plywood.
4. Place plywood onto mounting brackets and
align drilled holes with slots in mounting
brackets. Refer to
DE7025 Hardware
Selection Chart
and use either Method 1 or 2
to secure plywood to mounting brackets.
5. Use 13 mm wrench to tighten hardware.
6. The mitre saw should be mounted to the
plywood using holes in the mitre saw base. The
hardware size will be determined by the holes
in the mitre saw base. Hardware should be
31.8 mm longer than the maximum height of
the mitre saw base at each mounting location.
a.
Transfer location of mounting holes from
mitre saw base to plywood.
b.
Drill holes accordingly to the size of the
hardware chosen.
NOTE:
Hardware must
be purchased to mount mitre saw to
plywood. All purchased hardware should be
a minimum of Grade 5 or Class 8.8.
c.
Secure mitre saw to plywood as shown in
Figure 5. Saw base (e), 19 mm plywood (i),
flat washer (f), lock washer (h) and nut (g).
NOTE:
Ensure a flat washer (f) is used
between plywood (i) and lock washer (h).
d.
Tighten all hardware.
Removing the Saw
Once the mitre saw is fastened to the brackets,
it can be removed by grasping the release levers,
pulling up slightly to clear the beam and can be
set down on the rubber feet for transportation or
cleaning.
MAINTENANCE
Your D
E
WALT power tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Cleaning
WARNING:
Never use solvents or
other harsh chemicals for cleaning the
non-metallic parts of the tool. These
chemicals may weaken the materials
used in these parts. Use a cloth
dampened only with water and mild
soap. Never let any liquid get inside the
tool; never immerse any part of the tool
into a liquid.
Optional Accessories
WARNING:
Since accessories, other
than those offered by D
E
WALT, have
not been tested with this product, use
of such accessories with this tool could
be hazardous. To reduce the risk of
injury, only D
E
WALT recommended
accessories should be used with this
product.
Consult your dealer for further information on the
appropriate accessories.
COMPATIBLE PRODUCTS
DE7023 Heavy-duty mitre saw stand
DE7033 Compact mitre saw stand
DE7035 Heavy-duty work stand
Содержание DE7025
Страница 1: ...www eu DE7025 DE7030 ...
Страница 3: ...1 Figure 1 a c b Figure 2 d Figure 3 a a ...
