DeWalt DCS573 Series, Оригинальное руководство пользователя

Страница: 17 / 64

15
English
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start‑up can cause injury.
along cutting lines penciled on the material being cut. The kerf
indicator lines up with the left (outer) side of the saw blade,
which makes the slot or “kerf” cut by the moving blade fall to
the right of the indicator. Guide along the penciled cutting line
so that the kerf falls into the waste or surplus material.
Mounting and Adjusting the Parallel
Fence (Fig. N)
The parallel fence 22 is used for cutting parallel to the edge of
the workpiece.
Mounting
1. Slacken the parallel fence adjustment knob
23
to allow the
parallel fence to pass.
2. Insert the parallel fence
22
in the shoe as shown.
3. Tighten the parallel fence adjustment knob 23 .
Adjusting
1. Slacken the fence adjustment knob 23 and set the parallel
fence
22
to the desired width. The adjustment can be read
on the parallel fence scale.
2. Tighten the fence adjustment knob 23
Mounting the Dust Extraction Port (Fig. A, P)
Your circular saw is supplied with a dust extraction port.
To Install the Dust Extraction Port
1. Fully loosen depth adjustment lever 4 .
2. Place the shoe 5 in the lowest position.
3. Align the left half of the dust extraction port 24 over upper
blade guard 36 as shown. Be sure to insert the tab into the
casting notch on the tool. When installed correctly, it will
snap fully over the original depth of cut pointer.
4. Align the right‑hand piece
37
with the left.
5. Insert screws and tighten securely.
Prior to Operation
• Make sure the guards have been mounted correctly. The
saw blade guard must be in closed position.
• Make sure the saw blade rotates in the direction of the
arrow on the blade.
• Do not use excessively worn saw blades.
Any other conditions which could result in pinching,
binding, twisting, or misalignment of the blade could cause
kickback. Refer to the sections
Further Safety Instructions for
All Saws and Blades for procedures and techniques that will
minimize the occurrence of kickback.
Depth of Cut Adjustment (Fig. E, F)
1. Raise the depth adjustment lever 4 to loosen.
2. To obtain the correct depth of cut, align the appropriate
mark on the depth adjustment strap
30
with notch
31
on
the upper blade guard.
3. Tighten the depth adjustment lever.
4. For the most efficient cutting action using a carbide tipped
saw blade, set the depth adjustment so that about one half
of a tooth projects below the surface of the wood to be cut.
5. A method of checking for the correct cutting depth is
shown in Figure F. Lay a piece of the material you plan to
cut along the side of the blade, as shown in the figure, and
observe how much tooth projects beyond the material.
Adjusting Depth Adjustment Lever (Fig. E)
It may be desirable to adjust the depth adjustment lever
4
. It
may loosen in time and hit the shoe before tighten ing.
To Tighten the lever:
1. Hold depth adjustment lever 4 and loosen the locknut 32 .
2. Adjust the depth adjustment lever by rotating it in the
desired direction about 1/8 of a revolution.
3. Retighten nut.
Bevel Angle Adjustment (Fig. A, G)
The bevel angle adjustment mechanism can be adjusted
between 0 ° and 57 °.
To achieve better accuracy in cutting, use the fine adjustment
markings located on the pivot bracket
33 .
1. Raise the bevel adjustment lever 10 to loosen.
2. Tilt the shoe to the desired angle by aligning the fine
bevel pointer
35
with the desired angle mark on the pivot
bracket 33 .
3. Lower the bevel adjustment lever to retighten.
Bevel Detent (Fig. A, G)
The DCS573 is equipped with a bevel detent feature. As you
tilt the shoe
5 you will hear a click and feel the shoe stop
at both 22.5 and 45 degrees. If either of these is the desired
angle, retighten the lever
10 by lowering it. If you desire
another angle, continue tilting the shoe until the coarse bevel
pointer
34 or the fine pointer 35 aligns with the desired mark.
Cut Length Indicator (Fig. A)
The markings on the side of the shoe 5 show the length of the
slot being cut into the material at the full depth of the cut. The
markings are in increments of 5 mm.
Kerf Indicator (Fig. I)
The front of the saw shoe has a kerf indicator
9
for vertical
and bevel cutting. This indicator enables you to guide the saw