manualshive.com logo in svg

DeWalt DCS391-XE, Инструкция по эксплуатации

Поделиться
Скачать
DeWalt DCS391-XE Скачать руководство пользователя страница 17

  6. Start the motor and gradually lower the saw until its shoe rests flat on the 

material to be cut. Advance saw along the cutting line until cut is completed. 

  7. Release the trigger switch and allow the blade to stop completely before 

withdrawing the blade from the material. 

  8. When starting each new cut, repeat the above steps. 

NOTE:

 A smooth, even flow of dust from the hole indicates proper drilling rate.

MAINTENANCE

WARNING: To reduce the risk of serious personal injury, place the forward/

reverse button in the lock-off position or turn tool off and disconnect battery pack 

before making any adjustments or removing/installing attachments or accessories.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING:

 Blow dirt and dust out of all air vents with clean, dry air at least once 

a week. To minimize the risk of eye injury, always wear AS/NZS51337 approved eye 

protection when performing this. 

WARNING:

 Never use solvents or other harsh chemicals for cleaning the 

non-metallic parts of the tool. These chemicals may weaken the plastic materials 

used in these parts. Use a cloth dampened only with water and mild soap. Never let 

any liquid get inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: 

Shock hazard. Disconnect the charger from the AC outlet before 

cleaning. Dirt and grease may be removed from the exterior of the charger using a 

cloth or soft non-metallic brush. Do not use water or any cleaning solutions.

Repairs

The charger and battery pack are not serviceable. There are no serviceable parts 

inside the charger or battery pack. 
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment 

(including brush inspection and replacement) should be performed by certified 

service centers or other qualified service organizations, always using identical 

replacement parts.

ACCESSORIES

WARNING: 

Since accessories, other than those offered by D

E

WALT, have not been 

tested with this product, use of such accessories with this tool could be hazardous. 

To reduce the risk of injury, only D

E

WALT, recommended accessories should be used 

with this product. 

Recommended accessories for use with your tool are available at extra cost from 

your local service center. If you need any assistance in locating any accessory, please 

contact Stanley Black & Decker, 82 Taryn Drive, Epping, VIC 3076 Australia or call 

1800 444 224 or (NZ). 0800 339 258.

Содержание DCS391-XE





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды