16
English
Correcting a Cut
Should your cut begin to leave the cutting line, don’t try to
force it back on. Forcing a correction can stall the saw and
cause kickback. Instead, release the switch and allow the blade
to come to a complete stop. Then, back the saw out of the
cut. Restart the saw and re-enter the cut, following the desired
cutting line.
CAUTION:
Do not cut through bolts with the metal-
cutting saw. Damage to the saw or personal injury
could result.
Maximizing Blade Life
To extend blade life, follow these practices:
•
Do not force the blade through the metal. The saw must cut
at its own pace and at a constant rate.
•
Change blades when it is no longer easy to push the saw
through the cut, when the motor is straining, or when
excessive heat is built up in the blade.
•
Keep base of the saw firmly against metal you are cutting.
•
If the metal you are cutting is vibrating or shaking, clamp
the material as close to the cut as possible and slow down
the cutting rate.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
WARNING: Always wear proper personal hearing
protection.
Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
Instructions for Use
WARNING:
•
Always observe the safety instructions and
applicable regulations.
•
Ensure the material to be sawn is secured in place.
•
Apply only a gentle pressure to the tool and do not
exert side pressure on the saw blade. If possible, work
with the saw shoe pressed against the workpiece. This
prevents damage to the blade and stops the tool from
jerking and vibrating.
•
Avoid overloading.
•
Let the blade run freely for a few seconds before
starting the cut.
Proper Hand Position (Fig. J)
WARNING:
To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
14
, with the other hand on the auxiliary handle
15
, as shown
in Figure J, to guide the saw properly.
MAINTENANCE
Your
D
e
WALT
power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Replacing Sight Window (Fig. A)
WARNING:
Do not operate the saw with a damaged or
missing sight window. If window is damaged or missing,
have the saw serviced at an authorised service centre.
If the saw is operated without the window, metal chips
could fly through the guard and cause personal injury.
The sight window
10
must be replaced by an authorised
D
e
WALT
service centre.
CAUTION:
Do not use any cleaning fluids on the sight
window to avoid clouding it and compromising the safe
operation of the saw. Use compressed air to remove
accumulated dust from the inside of the sight window.
Wear safety glasses when performing this.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING:
Since accessories, other than those offered
by
D
e
WALT
, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT
recommended
accessories should be used with this product.
Use only 140 mm
D
e
WALT
metal-cutting blades with a
20 mm arbor.
Consult your dealer for further information on the
appropriate accessories.
Содержание DCS373N
