DeWalt DCS373, Оригинальное руководство пользователя

Страница: 50 / 228

ENGLISH
48
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
D
E
WALT service organization.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in
the plug.
• Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see
Technical Data ). The minimum conductor size
is 1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
serious personal injury, turn tool
off and disconnect battery pack
before making any adjustments or
removing/installing attachments or
accessories.
An accidental start-up
can cause injury.
WARNING: Use only D
E
WALT battery
packs and chargers.
Inserting and Removing the
Battery Pack from the Tool (fi g. 3)
NOTE: For best results, make sure your battery
pack is fully charged. The light will shut off without
warning when the battery is fully discharged.
TO INSTALL THE BATTERY PACK INTO THE TOOL HANDLE
1. Align the battery pack (i) with the rails inside the
tool’s handle (fig. 3).
2. Slide it into the handle until the battery pack is
firmly seated in the tool and ensure that it does
not disengage.
TO REMOVE THE BATTERY PACK FROM THE TOOL
1. Press the battery release button (m) and firmly
pull the battery pack out of the tool handle.
2. Insert battery pack into the charger as
described in the charger section of this manual.
FUEL GAUGE BATTERY PACKS (FIG. 4)
Some D
E
WALT battery packs include a fuel gauge
which consists of three green LED lights that
indicate the level of charge remaining in the battery
pack.
To actuate the fuel gauge, press and hold the fuel
gauge button (p). A combination of the three green
LED lights will illuminate designating the level of
charge left. When the level of charge in the battery
is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
NOTE: The fuel gauge is only an indication of the
charge left on the battery pack. It does not indicate
tool functionality and is subject to variation based
on product components, temperature and end-user
application.
Trigger Switch (fi g. 1)
WARNING: This tool has no provision
to lock the trigger switch in the ON
position and should never be locked ON
by any other means.
The saw is controlled by a trigger switch (a) and
lock-off button (b). The lock-off button must be
pressed before the trigger switch will turn the saw
on. Releasing the trigger turns the saw off.
Changing Blades (fi g. 1, 5–7)
TO INSTALL THE BLADE
1. Place inner clamp washer (q) on saw spindle (s)
with the large flat surface facing out toward the
blade (fig. 5, 6).
2. Retract the lower blade guard (g) and place
blade (t) on saw spindle against the inner
clamp washer (q), making sure that the blade
will rotate in the proper direction (the direction
of the rotation arrow on the saw blade and
the teeth must point in the same direction as
the direction of rotation arrow on the saw). Do
not assume that the printing on the blade will
always be facing you when properly installed.
When retracting the lower blade guard to install
the blade, check the condition and operation
of the lower blade guard to assure that it is
working properly. Make sure it moves freely and
does not touch the blade or any other part, in all
angles and depths of cut.
3. Place the outer clamp washer (r) on the saw
spindle (s) with the large flat surface against the
blade (t) with beveled side facing out.