DeWalt DCN650, Оригинальное руководство пользователя

Страница: 36 / 156

34
EnGLIsh
7
Magazine
8 Pusher
9
Bump/sequential selector switch
10 Belt hook
11
No-mar pad
12 No-mar pad storage
13
Stall release lever
14 Battery
15
Nail depth indicator
16
Battery release button
Intended Use
Your DCN650 (15GA) finish nailer has been designed for
professional nailing applications for wooden workpieces.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These DCN650 (15GA) finish nailers are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
WARNING: Use only D
e
WALT battery packs and chargers.
Belt Hook (Fig. A, C)
WARNING: Remove nails from magazine before making
any adjustments or servicing this tool. Failure to do so may
result in serious injury.
WARNING: Disconnect battery pack from tool before
making any adjustments, changing accessories,
servicing, or moving the tool.
Such preventative safety
measures reduce the risk of starting the tool accidentally.
CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping
or falling hazard.
Some tools with large battery packs
will stand upright on the battery pack but may be easily
knocked over.
The D
e
WALT cordless nailers include an integrated belt
hook
10
and can be attached to either side of the tool to
accommodate left- or right-handed users.
If the hook is not desired at all, it can be removed from the tool.
To remove belt hook
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage simply
remove the screw 19 from the opposite side of the tool and
reassemble on the other side.
3. Replace battery pack.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE:
Make sure your battery pack 14 is fully charged.
To Install the Battery Pack into the
Tool Handle
1. Align the battery pack 14 with the rails inside the tool’s
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 16 and firmly pull the battery pack
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
e
WALT battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Low Battery Indicator (Fig. A, B)
The low battery indicator is an integrated feature in the left-
hand worklight. It will blink 4 times to indicate that the battery
pack needs to be recharged and the tool will automatically
shut down.
Switch off the tool and take out the battery pack
14 to charge it
as soon as the indicator blinks.
The tool remains non-operational as long as a low battery pack
is attached to it.
Selecting the Mode (Fig. E)
To select sequential action mode, slide the mode selector
switch
9 to the single nail icon ( ).
To select bump action mode, slide the mode selector switch 9
to the three nail icon ( )
Non-mar Tip (Fig. A)
Place the no-mark tip
11
over the contact trip
6
when the tool
is used on wood.