DeWalt DCLE34220, Инструкция по эксплуатации, Страница: 18 / 68

18
E
(Figure
A 2
) and slide the pack out of the charger
(Figure
A 3
).
5.
Slide the battery pack down in the laser until it
snaps in place (Figure
A 4
).
Viewing the Battery Meter
When the laser is ON, the battery meter on the keypad
(Figure
C 9
) indicates how much power remains.
Each of the four LEDs on the battery meter represents
25% of the power.
• The bottom LED will illuminate and flash when the
battery level is low (below 12.5%). The laser may
continue to operate for a short time while the battery
power continues to drain, but the beam(s) will
quickly dim.
• After the 12V/20V MAX Li-ion battery is charged, and
the laser is turned ON again, the laser beam(s) will
return to full brightness and the battery indicator level
will indicate full capacity.
• If all 4 LEDs on the battery meter remain ON, this
indicates that the laser is not fully powered OFF.
When the laser is not in use, make sure the Power/
Transport Lock switch is placed to the LEFT to the
Locked/OFF position (Figure
C 2
).
Operating Tips
• To extend battery life per charge, turn the laser off
when it is not in use.
• To ensure the accuracy of your work, check
the laser calibration often. Refer to Checking
Laser Accuracy.
• Before attempting to use the laser, make sure it is
positioned securely, on a smooth, flat stable surface
that is level in both directions.
• To increase beam visibility, use a Laser Target Card
(Figure
O
) and/or wear Laser Enhancement Glass es
(Figure
P
) to help find the beam.
CAUTION:
To reduce the risk of serious injury, never
stare directly into the laser beam with or
without these glasses. Refer to Accessories for
important information.
• Always mark the center of the beam created by
the laser.
• Extreme temperature changes can cause movement
or shifting of building structures, metal tripods,
equipment, etc., which can effect accuracy. Check
your accuracy often while working.
• If the laser has been dropped, check to make sure
your laser is still calibrated. Refer to Checking
Laser Accuracy.
Turning the Laser On
Place the laser on a flat level surface. Slide the Power/
Transport Lock switch
C 2
to the right to unlock/turn
ON the laser.
Button Displays
• Press once to display a horizontal laser
line (Figure
C 4
).
• Press a second time to display a
vertical laser line (Figure
C 5
).
• Press a third time to display a
horizontal line and a vertical line
(Figure
C 6
).
• Press a fourth time to stop displaying
laser lines.
DCLE34220
DCLE34520
1b
1a
3a
3b
3c
3d
3e
3f
x3
x2
x1
x2
x3
x1
x2
Figures
2
1
2
A
B
C
1
2
1/4-20
5/8-11
3
3
• Press once to display dots above and
below the laser (Figure
C 7
).
• Press a second time to stop
displaying dots.
You can use and /
1b
1a
3a
3b
3c
3d
3e
3f
x3 x2
x1
x2
x3
x1
x2
Figures
2
1 2
A
B
C
1
2
1/4-20
5/8-11
3
3
together to display laser
dots and lines. For example, if you press three
times and /
1b
1a
3a
3b
3c
3d
3e
3f
x3 x2
x1
x2
x3
x1
x2
Figures
2
1 2
A
B
C
1
2
1/4-20
5/8-11
3
3
once, the laser will display cross lines
and two dots (Figure
C 8
).