![background image](http://html.mh-extra.com/html/dewalt/dcle34030/dcle34030_instruction-manual_88289019.webp)
19
E
• The bracket has magnets (Figure
J
1
) which allow
the unit to be mounted to most upright surfaces
made of steel or iron. Common examples of suitable
surfaces include steel framing studs, steel door
frames, and structural steel beams. Before attaching
the pivot bracket against a stud (Figure
J
2
), place
the Metal Enhancement Plate (Figure
J
3
) on the
opposite side of the stud.
Maintenance
• To maintain the accuracy of your work, check the
laser often to make sure it is properly calibrated.
See Field Calibration Check.
• Calibration checks and other maintenance repairs
may be performed by D
E
WALT service centers.
• When not in use, store the laser in the kit box
provided. Do not store your laser at temperatures
below -5˚F (-20˚C ) or above 140˚F (60˚C).
• Do not store your laser in the kit box if the laser is
wet. The laser should be dried first with a soft dry
cloth prior to storage.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth.
Although these parts are solvent resistant, NEVER use
solvents. Use a soft, dry cloth to remove moisture from
the tool before storage.
Troubleshooting
The Laser Does Not Turn On
• Fully-charge the battery pack and then reinstall it in
the laser unit.
•
If the laser unit is heated above 120˚F (50˚C), the
unit will not turn on. If the laser has been stored in
extremely hot temperatures, allow it to cool. The
laser level will not be damaged by pressing the on/
off button before cooling to its proper operating
temperature.
The Laser Beams Flash
The lasers are designed to self-level up to an average
of 4° in all directions If the laser is tilted so much that
the internal mechanism cannot level itself, the laser
beams will flash indicating that the tilt range has been
exceeded. THE FLASHING BEAMS CREATED BY THE
LASER ARE NOT LEVEL OR PLUMB AND SHOULD
NOT BE USED FOR DETERMINING OR MARKING
LEVEL OR PLUMB. Try repositioning the laser on a
more level surface.
The Laser Beams Will Not Stop Moving
The laser is a precision instrument. Therefore, if it is
not positioned on a stable (and motionless) surface,
the laser will continue to try to find level. If the beam
will not stop moving, try placing the laser on a more
stable surface. Also, try to make sure that the surface is
relatively flat, so that the laser is stable.
The Battery Meter LEDs Flash
When all 4 LEDs continuously flash on the Battery
Meter this indicates that the unit has not been fully
powered off using the Power/Transport Lock switch
(Figure
C
2
). The Power/Transport Lock switch should
always be placed in the LOCKED/OFF position when
the laser is not in use.
Accessories
The laser is equipped with both 1/4 - 20 and 5/8 - 11
female threads on the bottom of the unit (Figure
K
).
This thread is to accommodate current or future D
E
Walt
accessories. Only use D
E
Walt
accessories specified
for use with this product. Follow the directions included
with the accessory.
WARNING:
Since accessories, other than those
offered by D
E
Walt, have not been tested with
this product, use of such accessories with this
Содержание DCLE34030
