DeWalt DCG4610, Оригинальное руководство пользователя

Страница: 41 / 172

39
EngLIsh
Proper Hand Position (Fig. H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
5
,
with the other hand on the body of the tool, as shown
in Figure H.
Trigger Switch and Lock-off Lever (Fig. A)
WARNING:
Before using the tool, check that the handle is
tightened securely.
1. To turn the tool on, push the lock-off lever
2
toward the
back of the tool, then depress the trigger switch 1 . The tool
will run while the switch is depressed.
2. Turn the tool off by releasing the releasing switch.
WARNING: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops rotating.
Make sure the wheel has come to a complete stop be fore
laying the tool down.
WARNING:
Allow the tool to reach full speed before
touching tool to the work surface. Lift the tool from the
work surface before turning the tool off.
Spindle Lock (Fig. A)
The spindle lock 3 is provided to prevent the spindle from
rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged from
the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button 3
and rotate the spindle until you are unable to rotate the
spindle further.
Tuckpointing and Cutting Application
(Fig. A, H)
1. Set the desired depth of cut, see Depth of Cut Adjustment
under assembly and adjustments.
2. Allow the tool to reach full speed before touching it to the
work surface.
3. Position yourself so the open underside of the shroud and
the wheel are facing away from you.
4. Place the depth of cut shoe 10 of the shroud onto the work
surface and begin cut by plunging into the work surface.
The upper shroud
16
will lock onto the lower shroud
17
after the initial plunge.
nOTE: Keep the depth of cut shoe of the shroud against the
work surface to ensure proper dust collection.
5. With the shroud oriented as shown in Figure H, pull the
cut-off tool along the work surface.
nOTE: The cut-off tool should ONLY be used in the
direction indicated.
6. When finished with the cut, remove the tool from work
surface before turning off the tool. Allow the tool to stop
rotating before laying it down.
7. Push the side shroud button
15
to release the upper
shroud and start a new plunge and cut.
MAINTENANCE
Your D
e
WALT power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
e
WALT , have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
D
e
WALT recommended
accessories should be used with this product.
WARNING: Accessories must be rated for at least the
speed recom mended on the tool warning label. Wheels
and other accessories running over rated speed can fly
apart and cause injury. Accessory ratings must always be
above tool speed as shown on tool nameplate. Select an
appropriate blade for the cutting application.
Consult your dealer for further information on the
appropriate accessories.