29
EngLIsh
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
WARNING:
Use only
D
E
WALT
battery packs and chargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE:
Make sure your battery pack
8
is fully charged.
To Install the Battery Pack into the Tool
1. Unlatch and open the battery door
6
as shown in Figure B.
2. To install the battery pack
8
into the tool, align the
battery pack with the rails inside the tool and slide it in
until the battery pack is firmly seated. Ensure that it does
not disengage.
3. Close the battery door and ensure it is closed securely.
To Remove the Battery Pack from the Tool
1. To remove the battery pack from the tool, unlatch and open
the battery door
2. Press the release button
9
and firmly pull the battery pack
out of the tool.
3. Insert battery pack into the charger as described in the
charger section of this manual.
4. Do not leave the battery door open.
Fuel Gauge Battery Packs (Fig. B)
Some
D
e
WALT
battery packs include a fuel gauge which
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
10
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE:
The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Inserting and Removing a Paddle (Fig. C)
1. Insert the paddle thread into paddle holder
4
by turning
it clockwise.
2. Tighten the paddle with the 2 included wrenches.
3. To remove the paddle, proceed in reverse order.
D
E
WALT
ToolConnect Tag Ready (Fig. E)
Optional Accessory
Your mixer comes with mounting holes
11
and screws
for installing a
D
e
WALT
ToolConnect Tag. You will need
a cross bit tip to install the tag with the provided screws.
The
D
e
WALT
ToolConnect Tag is designed for tracking and
locating professional power tools, equipment, and machines
using the
D
e
WALT
Tool Connect app. For proper installation
of the
D
e
WALT
ToolConnect Tag refer to the
D
e
WALT
ToolConnect manual.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING:
To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on each dual handle
5
.
Running the Mixer (Fig. A)
WARNING:
• Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids
labelled accordingly.
• Always check the flammability warnings on any
product before attempting to mix.
1. Hold the mixer with both hands.
2. To start the unit, press the lock off lever
2
and then the
trigger
1
can be pulled in, turning on the unit.
3. To stop the tool, release the trigger.
During the mixing process you should guide the mixer around
the container to ensure a more consistent mix. Continue until all
of the material is completely mixed.
nOTE:
Please follow the processing instructions of the
manufacturer of the material.
Always be aware that the greater the viscosity of the material,
the greater the impact of the torque forces on the mixer.
CAUTION:
If the mixer comes into contact with the
surface of the mixing container while running, it may
kick back.
Variable Speed Dial (Fig. A)
WARNING:
Always switch off the tool when work is
finished and before removing the battery.
The variable speed dial
3
offers added control and enables the
mixer to be used at optimum conditions to suit the material.
Содержание DCD240
