ENGLISH
26
DO NOT
use under humid conditions or in presence
of flammable liquids or gases.
These nailers are professional power tools.
DO
NOT
let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
ASSEMBLY AND ADJUSTMENTS
WARNING:
Prior to assembly and
adjustment,
ALWAYS
lock-off trigger,
disconnect air line from tool and remove
fasteners from the canister before
making and adjustments or personal
injury may result.
Trigger
WARNING:
Keep fingers AWAY from
trigger when not driving fasteners to
avoid accidental firing. Never carry tool
with finger on trigger. In Contact Bump
Actuation Mode tool will fire a fastener
if safety is bumped while trigger is
depressed.
These tools are assembled with a bump action
trigger. A sequential action trigger is also included
with the original packaging. For definitions of “bump
action” and “sequential action”, see below.
The
gray trigger
with
imprinted on the side is
the single sequential action trigger and causes the
tool to operate in this mode.
The
black trigger
with
imprinted on the side is
the bump action trigger and permits the tool to be
actuated in this manner.
For defining the use of the sequential action trigger
and bump action trigger, see
Actuating the Tool
.
TRIGGER REMOVAL (FIG. 2)
1. Remove rubber grommet (j) from the end of the
dowel pin (k).
2. Remove dowel pin.
3. Remove trigger assembly from trigger cavity
under the handle of the tool housing.
TRIGGER INSTALLATION (FIG. 2)
1. Select either the sequential or bump action
trigger to be installed on the tool. Both triggers
are included in the tool packaging.
2. Insert the trigger kit into trigger cavity.
3. Ensure that trigger spring (l) is placed around
the trigger valve stem (m).
4. Align the holes of the trigger with the housing
holes (n), then insert the dowel pin (k) through
the entire assembly as shown.
5. Push the rubber grommet (j) onto the end of the
dowel pin as shown.
Air Fitting (fi g. 1)
These tools have a standard 3/8" pipe thread for
the air fitting. The tool is assembled with a 3/8"
to 1/4" adapter installed in the end cap.
• Wrap the male end of the fitting with thread seal
tape to prevent air leaks.
• To install a 1/4" fitting, screw the fitting into the
3/8" to 1/4" adapter in the end cap and tighten
firmly.
• To install a 3/8" fitting, remove the 3/8" to 1/4"
adapter, if present. Screw the fitting into the end
cap and tighten firmly.
OPERATION
Instructions for Use
WARNING: ALWAYS
observe the
safety instructions and applicable
regulations.
WARNING: ALWAYS
place workpiece
safely.
Preparing the Tool (fi g. 1)
WARNING:
To reduce the risk of
personal injury, disconnect tool from air
supply before performing maintenance,
clearing a jammed fastener, leaving work
area, moving tool to another location or
handing the tool to another person.
WARNING:
Wear proper eye, hearing
and respiratory protection.
NOTE:
These nailers are designed to be used
without oil. If preferred, 10–15 drops of oil may be
used on o-rings, rubber parts and can be applied to
the air fittings.
• Drain all condensation from the air compressor
tanks and hoses.
• Remove all nails from the canister.
• Check if the contact trip (f) can move freely.
WARNING:
Do not use the tool if the
contact trip or nail pusher cannot move
freely.
Содержание D51855
Страница 1: ...D51855 www eu ...
Страница 3: ...1 Figure 1 a g f i d c h b e Figure 2 j k n m k l j ...
Страница 4: ...2 Figure 3 Figure 4 a p s q r t g Figure 5 o ...
Страница 131: ...129 ...
