5
•
NEVER STAND ON TOOL
.
Serious injury could occur if the tool is tipped or if the
cutting tool is unintentionally contacted.
•
CHECK DAMAGED PARTS.
Before further use of the tool, a guard or other part that
is damaged should be carefully checked to determine that it will operate properly
and perform its intended function — check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and any other conditions that may
affect its operation. A guard or other part that is damaged should be properly
repaired or replaced.
•
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF.
Don’t leave tool
until it comes to a complete stop.
•
REPLACEMENT PARTS.
When servicing use only identical replacement parts.
•
TO REDUCE THE RISK OF ELECTRIC SHOCK:
a. The tool may be equipped with a 3-prong grounding type plug. This plug is to
be used in a grounded outlet only. If the plug does not fit, contact a qualified
electrician to install the proper outlet.
b. Do not alter the plug in any way.
Electrical Safety
The electric motor has been designed for one voltage range only. Always check that
the power supply corresponds to the voltage on the rating plate. 220–240 V AC
means your tool will operate on alternating current. Operation at a voltage outside this
range can cause loss of power and can result in overheating. All D
E
WALT tools are
factory tested; if this tool does not operate, check the power supply. Your D
E
WALT
tool is double insulated, therefore no earth wire is required.
•
Young children and the infirm.
This appliance is not intended for use by young
children or infirm persons without supervision.
– This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
– Children should be supervised to ensure that they do not play with the appliance.
•
Replacement of the supply cord.
If the supply cord or plug is damaged, it must
be replaced by the manufacturer or an authorised D
E
WALT Service Centre in
order to avoid a hazard.
Extension Cords
CAUTION:
Use only extension cords that are approved by the country’s Electrical
Authority. Before using extension cords, inspect them for loose or exposed wires,
damaged insulation and defective fittings. Replace the cord if necessary.
Additional Safety Rules for Chop Saw
• Always wear proper eye and respiratory protection.
• Before using, inspect the cutting wheel for cracks or flaws. If such a crack
or flaw is evident, discard the wheel. The wheel should also be inspected
whenever you think the tool may have been dropped. Flaws may cause wheel
breakage.
• When starting the tool with a new or replacement wheel or if you are unsure of
the condition of the wheel, hold the tool in a well protected area and let it run
for one minute.
If the wheel has an undetected crack or flaw, it should burst in
less than one minute. Never start the tool with a person in line with the wheel.
This includes the operator.
•
In operation, avoid bouncing the wheel or giving it rough treatment.
If this
occurs, stop the tool and inspect the wheel for cracks or flaws.
•
Never have any part of your body in line with the path of the saw blade.
Personal injury will occur.
• Clean your chop saw periodically following the procedure in this manual.
• Do not remove wheel guards or base.
•
Always use the vise or special fixture to clamp work securely.
Other aids such
as spring, bar, or C-clamps may be appropriate for certain sizes and shapes of
workpiece. Use care in selecting and placing these clamps and make a dry run
before making a cut.
• Use only 355 mm (14") type 1 wheels rated at 4100 rpm or higher.
• Allow cut off parts to cool before handling.
• Do not attempt to cut wood or plastic with this tool.
•
NEVER CUT MAGNESIUM WITH THIS TOOL.
• Use chop saw in a well-ventilated area.
• Turn chop saw off before removing any pieces from the base.
Содержание D28715-XE
Страница 1: ...D28715 XE HEAVY DUTY 355 mm 14 CHOP SAW WITH QUICK CHANGE CLAMP INSTRUCTION MANUAL ...
Страница 2: ......
