background image

7

   Icon 

Description 

Purpose

    

 20

φ

 Cone nozzle 

Welding, shrink sleeving 

 

 

(heat concentrated over 

  

 

small 

area)

   

 

50 mm Fish tail  

Drying, thawing 

 

surface nozzle 

(heat spread 

 

 

over wide area)

  1.   Make sure the on/off switch (A) is in position "O" and the tool is disconnected 

from the power source. Ensure the nozzle has cooled down.

  2.   Place the desired accessory onto the nozzle.

OPERATION

WARNING: To reduce the risk of serious personal injury, turn tool off and 

disconnect tool from power source before making any adjustments or removing/

installing attachments or accessories.

WARNING: 

Make sure the nozzle ALWAYS points away from you and any 

bystanders.

WARNING: 

DO NOT drop anything into the nozzle.

WARNING: 

Use only one hand to hold the tool as shown in Figure 2. Do not place 

your other hand over the air vents (Fig. 3).

PRIOR TO OPERATION

  1.  Attach the correct accessory recommended for the application.
  2.   Turn the air temperature adjustment knob (D) to desired air temperature.

FIG. 2

FIG. 3

Switching On and Off (Fig. 4)

  1.  Push the on/off switch (A) to the desired air flow settings: 
    1.24 liter/min [50

˚

 C-400

˚

 C 122–752º F)]

      A low air flow to heat up the workpiece slowly.
    11.45 liter/min [50

˚

 C-600

˚

 C (122–1112º F)]

      A high air flow to heat up the workpiece quickly.
  2.   To turn the tool off, push    

A

FIG. 4

 

the on/off switch (A) to 

position O. Disconnect the 

tool from the power source 

and let the tool cool down 

before moving or storing it.

Stripping Paint

WARNING:

 

Refer to

 

Important Notice

 under 

Additional Safety Instructions 
for Heat Guns 

before using the 

tool to remove paint.

WARNING: 

Do not strip 

metal window frames as the 

heat may crack the glass.

•   When striping other window frames, use the glass protection nozzle.
•   To prevent igniting the surface, do not keep the tool directed at one spot too 

long.

•   Avoid collecting paint on the scraper accessory, as it may ignite. If 

necessary, carefully remove paint debris from the scraper accessory using 

a knife.

  1.  Attach the appropriate accessory.
  2.  Turn the air temperature adjustment knob (D) to high.
  3.  Turn the tool on by selecting the desired air flow.

Содержание D26411-XE













Отзывы: