DeWalt D25893, Оригинальное руководство пользователя

Страница: 8 / 12

6
English
Side Handle (Fig. B)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 2 clamps to the front of the gear case and may
be rotated 360˚ to permit right- or left-hand use.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Active Vibration Control (AVC) System
For best vibration control, hold the tool as described in Proper
Hand Position and apply just enough pressure so the damping
device on the main handle is approximately mid stroke.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make the
tool chip faster and active vibration control will not engage.
D
e
WALT Tool Tag Ready (Fig. A)
Optional Accessory
Your hammer comes with D
e
WALT tool tag mounting holes
9
and fasteners for installing a D
e
WALT Tool Tag. You will need a
T20 bit tip to install the tag. The D
e
WALT Tool Tag is designed
for tracking and locating professional power tools, equipment,
and machines using the
D
e
WALT Tool Connect™ app. For proper
installation of the D
e
WALT Tool Tag refer to the D
e
WALT Tool
Tag manual.
Electronic Speed and Impact Control (Fig. A)
The electronic speed and impact control allows optimal tool
control for precise chiseling.
To set the electronic speed and impact control dial
8 , turn the
dial to the desired level. The higher the number, the greater
the speed and impact energy. Dial settings make the tool
extremely flexible and adaptable for many different appli cations.
The required setting depends on the bit size and hardness of
material being chiseled.
• When chiselling soft, brittle materials or when minimum
break-out is required, set the dial to a low setting;
• When breaking harder materials, set the dial to a
high setting.
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Mounting the Side Handle Assembly (Fig. B)
1. Widen the ring opening 12 of the side handle 2
by rotating the screw for side handle mounting 10
anti-clockwise.
2. Slide the assembly onto the nose of the tool, through the
steel ring
12
and onto the collar
3
, past the chisel holder
and sleeve.
3. Rotate the side handle assembly to the desired position.
4. Lock the side handle mounting assembly in place by
securely tightening the screw for side handle mounting 10
rotating it clockwise so that the assembly will not rotate.
Bit and Bit Holder
WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.
WARNING: Do not attempt to tighten or loosen chisel bits
(or any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may occur.
The chipping hammer can be fitted with various chisel bits
depending on the desired application.
Use sharp bits only.
Inserting and Removing SDS MAX Bits (Fig. C)
nOTE: Accessories and attachments used must be lubricated
around the SDS fitment before installation.
1. Pull back the locking sleeve 7 and insert the bit shank. The
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
nOTE:
The bit needs to move several centimeters in and out
of the tool holder 6 when properly engaged.
4. To remove the bit, pull back the locking sleeve and pull the
bit out.
Bit Position Adjustment
Turn the mode selector to bit adjustment icon (Refer to Mode
Selection ) to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel.
nOTE: After finding the desired position, slightly maneuver
the chisel bit back and forth to ensure the chisel is
properly engaged.