DeWalt D25481, Оригинальное руководство пользователя

Страница: 22 / 92

20
EngLIsh
Bit and Bit Holder
WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.
WARNING: Do not attempt to tighten or loosen drill bits
(or any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck and
personal injury may occur.
The rotary hammer can be fitted with various chisel bits
depending on the desired application.
Use sharp drill
bits only.
Inserting and Removing SDS Bits (Fig. C)
1. Pull back the locking sleeve
8
and insert the bit shank. The
bit shank must be clean.
2. Turn the bit slightly until the sleeve snaps back into position.
3. Ensure the bit is properly engaged.
nOtE: The bit needs to move several centimeters in and out
of the bit holder
7
when properly engaged.
To remove the bit, pull back the locking sleeve and pull the
bit out.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the mounted side
handle, with the other hand on the main handle.
Overload Clutch
In case of jamming of a drill bit, the drive to the drill spindle
is interrupted by the overload clutch. Due to the resulting
forces, always hold the tool with both hands and take a
firm stance. After the overload, release and depress the trigger
to re-engage drive.
Mechanical Clutch
These tools are fitted with a mechanical clutch. The indication
that the clutch has activated will be an audible ratcheting
together with increased vibration.
WARNING: Drill may stall if overloaded causing a sudden
twist. Always expect the stall. Grip the drill firmly to control
the twisting action and avoid injury.
Operation Modes (Fig. E)
WARNING: Do not select the operating mode when the
tool is running.
CAUTION: Never use in Rotary Drilling or Rotary
Hammering mode with a chisel bit in the bit holder.
Personal injury and damage to the the tool may result.
Your tool is equipped with a mode selector dial
4
to select the
mode appropriate to desired operation.
symbol Mode application
Rotary Drilling Dry diamond coring
Rotary
hammering
Drilling into concrete and masonry
hammering only Light chipping
to select an operating mode:
1. Depress the mode selector release button 5 .
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOtE: The arrow on the mode selector dial 4 must be pointing
at a mode symbol at all times. There are no operable positions
in between. It may be necessary to briefly run the motor after
having changed from 'hammering only' to 'rotary' modes in
order to align the gears.
Performing an Application (Fig. A, E)
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/or
bit onto to the tool. Refer to Bit and Bit Holder .
2. Using the mode selector dial
4
, select the mode
appropriate to desired application. Refer to
Operation Modes .
3. Adjust the side handle 2 as necessary.
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
1 .
6. To stop the hammer, release the switch.
Recommendations for Tool Operation
• When drilling, always apply pressure in a straight line with
the bit, but do not push hard enough to stall the motor or
deflect the bit. A smooth even flow of material indicates the
proper drilling rate.
• Your hammer can be used for dry diamond drilling into
masonry up to 100 mm. For diamond drilling above this
diameter in masonry and regular large diameter diamond
drilling in masonry and concrete, we advise the use of
a dedicated diamond core drill. Follow the core bit or
manufacturer’s recommendations for using the accessory.