Quick Install Adaptor
Dome Base
Camera Module
Camera Liner
Dome Cover
Locking Arms
Tighten tamper-proof screw
1
2
3
4
5
6
Installation
Preparation before installation
Use the template (see overleaf) to mark-out and prepare the mounting area.
In order to mount the base, first remove the camera module by gently pulling
down on the tabs that hold the camera module in place (see image right) and
remove camera assembly. To re-assemble gently pull down on the tabs and
insert the camera assembly.
Using the base mounting holes:
When mounting the dome to a ceiling or wall using screws, first knock out the
screw access holes that correspond to the template
marks “T1”.This can be
done by using a cross-point screwdriver.
Push the cables through the dome base and 3/4” rubber grommet.
Install the grommet on the base to prevent dust ingress. Cables may be routed
through the mounting surface if an appropriate hole is made at location T2.
If using the side knock-out, make sure the video-power cables are properly
arranged in the cable notch and exit out of the side knock without being
crushed (see image A).
Using the Quick Install Adaptor(Optional):
When mounting the dome to a ceiling using the quick install adaptor, use the
template to cut a hole as the circle marked “T2” with a hole cutter.
Install the adaptor into the mounting surface and use the screws to adjust the
position of the two locking arms on the quick install adaptor to adjust to the
mounting surface.
Push the cables through the opening and 1/2” rubber grommet.
Make sure the grommet is properly installed on the adaptor to prevent dust
ingress (see image B).
Mount on a US Single Gang Box:
When mounting the dome to the box, carefully remove the screws on the
box.Install the 3/4“ grommet on the base to prevent dust ingress, then push
the cables through the dome base and 3/4” rubber grommet.
Mount the dome base on the box and reinstall the two screrws.
Tighten the screws sufficiently on the box (position T1, see image C).
Removing the dome cover and the camera liner
Gently turn the dome cover counter-clockwise to unlock and pull free of the
dome base. Remove the camera liner by gently pulling it free of the 4 notches
in the camera base (see image A).
Opening the required knock-out panel
Open one of the side knock-outs (see image A) to the size required to allow
cable entry.
Replace the dome cover
Replace the dome cover and rotate clockwise to close it (as shown in image 5).
Install the camera liner
Carefully fit the camera liner over the camera base so that it snaps into place
(as shown in image 4), and do not obstruct the camera lens.
Install camera module
Push the video-power cables through the opening
Feed the pre-connected video-power cables through the appropriate point.
Then push the cable out of the opening. Make sure the cable is positioned on
the proper location and out of the side knock-out, if required.
Adjust the camera position
You can adjust the camera position by rotating and panning the camera base
(see image 3).
The focus and range of the lens can be adjusted (depending on the lens, see
instructions overleaf).
Mount the dome enclosure
By using the base mounting holes, the dome base can be fixed on the wall or
ceiling with attached screws.
Note:
When using Quick Install Adaptor, re-assemble the parts of dome, then
mount the whole dome onto adaptor (see image B).
Tighten the tamper-proof screw
Use the supplied torx driver and the tamper-proof screw (T2x5L) to secure the
dome cover (see image 6).
A.
B.
C.
1.
2.
3.
4.
5.
6.
Use the quick install adaptor on a wall or ceiling application.
ROTATE 360°
PAN 360°
TILT 90°
Tamper-proof Screw
Install the Dome Liner on the Camera Module
US Single Gang Box
Dome Base
T1
T1
C.Mount on a pre-installed US Single Gang Box
3/4”
Rubber Grommet
Video-Power Cables
Mounting Surface
1/2”Rubber Grommet
B.Mount with the Quick Install Adaptor
Side
Knock-outs
Mounting Surface
A.Mount with the Dome Base
Cable Notch
Cable Notch
3/4”
Rubber Grommet
PULL
Loosen the tab and pull out the camera assembly
