Devantech ETH008 Скачать руководство пользователя | Manualshive

Страница: 16 / 17

background image

Once the file has been opened the programming sequence will now begin, it's fairly short and following it's completion
the board will reset (automatically) and the LED will flash quickly while the programming sequence completes. Do not
turn the power off in this sequence.

Factory Reset

Should it be necessary to reset the ETH8020 to its shipped condition then the end two contacts of the row of 5 holes
near the large chip on the side nearest the Ethernet connection must be shorted together at board power up. Keep the
pins shorted until the green power LED starts to flash, this will take up to 5 seconds. The green LED will flash as the
settings are reset, please wait until the LED finishes flashing and do not remove power during this period.

© Devantech Ltd 02/07/19

ETH8020 Documentation

16/17

«
...
14
15
16
17
»

Содержание ETH008


















Отзывы:

Нет отзывов

Похожие инструкции для ETH008

Бренд: GE Страницы: 280

Бренд: P&B Страницы: 27

Бренд: National Instruments Страницы: 16

Бренд: EVERSPRING Страницы: 3

Бренд: W&T Страницы: 30

Бренд: Greystone Energy Systems Страницы: 2

Бренд: Schweitzer Engineering Laboratories Страницы: 142

Бренд: F&F Страницы: 3

Бренд: F&F Страницы: 4

Бренд: F&F Страницы: 2

Бренд: F&F Страницы: 2

Бренд: F&F Страницы: 6

Бренд: Theben Страницы: 7

Бренд: ABB Страницы: 32

Бренд: GE Страницы: 36

Бренд: GE Страницы: 4

Бренд: Omron Страницы: 4

Бренд: Omron Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды