DEVA Broadcast DB7012 Скачать руководство пользователя страница 23

65 Aleksandar Stamboliyski Str., 8000 Bourgas, Bulgaria

Tel: +359 56 820027, Fax: +359 56 836700

E-mail: [email protected] ,Web: www.devabroadcast.com

- 23 -

Timer

Represents relative time interval. 

Example: 

Front panel buttons usage: 

[UP] / [DOWN] – Increments/decrements value with one step. The unit value will be changed 

automatically from seconds to minutes and vice-versa; 

[OK] – Accept the changed value and exit edit mode; 

[SB4] – Discards all changes and cancels edit mode. 

String

Represents string. 

Example: 

Front panel buttons usage: 

[LEFT] / [RIGHT] – Select edit marker position. If [RIGHT] button is pressed when the marker 

is at the last character, a space character will be added at the end of the string. When the [LEFT] 

button is pressed all trailing spaces will be removed; 

[UP] / [DOWN] – Cycle through the possible values. Depending on the string context there 

is  a  limitation  in  the  permitted  char  set.  For  example  phone  number  string  can  contain  only 

123

 and blank space characters; 

[OK] – Accept the changed value and exit edit mode. Some strings, like e-mail addresses, must 

pass a validation check. If the validation fails, message box will appear. Press [OK] to dismiss the 

message. Note that edit mode will not be left. For example:

If [OK] is pressed

If [OK] is pressed

Содержание DB7012
































































Отзывы: