Detex ADVANTEX 82 Series Скачать руководство пользователя

Страница: 13 / 18

104888 Page 13

Level device before installing endcap bracket

Ensure that device does not require cutting (see Step 10g on next page).

Test device fuction after installation of endcap is complete by depressing
& releasing pushpad. Action should be smooth with full return of pushpad
and latch travel.

STEP 10:

HANG DOOR / ASSEMBLE DEVICE TO DOOR

Mark & drill holes for endcap bracket scews

10a

Install screws & lockwashers

4 places

10c

COMPLETE BACKPLATE MOUNTING

REFER TO TRIM INSTRUCTIONS AT THIS TIME, IF APPLICABLE

10b

10e

10d

INSTALL ENDCAP BRACKET

INSTALL DEVICE TO BACKPLATE

10f

INSTALL DOOR ONTO FRAME PER MANUFACTURER'S SPECIFICATIONS

If using sexnuts, install
here.

Right Hand Reverse

(RHR)

If link is not in uppermost position on the centerlift,

carefully remove "E" clips and reposition link on
top pin of the centerlift and replace "E" clips.

Verify carriage moves up and down smoothly when

pushpad is depressed and released.

Rehanding procedure

if required

HANDING INDICATOR

ON CENTERLIFT

Left Hand Reverse

(LHR)

MOVE LIFT PIN & SETSCREW TO

BOTTOM POSITION ON CARRIAGE.

LIFT PIN

MUST

BE ON

BOTTOM

Remove setscrew then liftpin which

screws out of the back.

NOTE: LINK MUST ALWAYS

BE IN TOP POSITION

setscrew

liftpin

Lift pin protruding from back of centercase

MUST

be inserted

BETWEEN

these two tabs.

Door OPEN position,
latches RETRACTED

Install device to backplate & fasten with 2 screws.
Depress pushpad appropriate amount to line up
lift pin with tabs.

Содержание ADVANTEX 82 Series



















Результаты поиска

Содержание ADVANTEX 82 Series

Отзывы:

Похожие инструкции для ADVANTEX 82 Series

Бренды по названию

Популярные бренды

Detex ADVANTEX 82 Series, Руководство по установке

Результаты поиска

Содержание ADVANTEX 82 Series

Отзывы:

Похожие инструкции для ADVANTEX 82 Series

Бренды по названию

Популярные бренды