Detex ADVANTEX 82 Series Скачать руководство пользователя

Страница: 1 / 18

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045

830-629-2900 / 800-729-3839 / Fax 800-653-3839 / Text photos only: 830-481-6433 / INTERNET: www.detex.com

104888 March 18, 2020

INSTALLATION INSTRUCTIONS FOR CONCEALED VERTICAL ROD

104888 Page 1

Concealed Vertical Rod Exit Device
82 / F82 / 83 / F83 Series

for Medium to Wide Stile
Aluminum or FRP door applications

Drawing No. 105280

Table of Contents Page

Device parts breakdown view................................................

Device parts breakdown list with part numbers.....................

Hardware List with part numbers & tools required................. 4

Step 1: Door/opening measurements....................................

Step 2: Door & frame prep ...................................................

Step 3: Top rod assembly and initial adjustment .................

7 & 8

Step 4: Bottom rod / latch assembly initial adjustment .........

Step 5: Visual alignment check ............................................

Step 6: Install top latch mounting bracket ............................

Step 7: Insert rod / latch / centerlift assembly into door .......

Step 8: Secure rod / latch / centerlift assembly to door .......

Step 9: Verify centerlift mechanism operation ...................

Step 10: Hang door / assemble device to door ....................

Check device for clearance ....................................

Install mortise cylinder ...........................................

Step 11: Install top strike.......................................................

Step 12: Install bottom strike.................................................

Step 13: Fine latch adjustment .............................................

Step 14: Install covers ..........................................................

Step 15: Install auxiliary bolt.................................................... 17

Optional accessories ............................................................

For device installation videos,

scan code below or

go to www.detex.com/videos

Owner's Copy

For WARRANTY information,

scan code below or

go to www.detex.com/warranty

Should you have a Question/Problem with your Detex device please
call Detex Technical Support from the job site at 1-800-729-3839
and choose option 2 on our menu. Please do not return the product

to the distributor.

Содержание ADVANTEX 82 Series



















Результаты поиска

Содержание ADVANTEX 82 Series

Отзывы:

Похожие инструкции для ADVANTEX 82 Series

Бренды по названию

Популярные бренды

Detex ADVANTEX 82 Series, Руководство по установке

Результаты поиска

Содержание ADVANTEX 82 Series

Отзывы:

Похожие инструкции для ADVANTEX 82 Series

Бренды по названию

Популярные бренды