manualshive.com logo in svg

Detectortesters Testifire 1000, Руководство пользователя

Поделиться
Скачать
Detectortesters Testifire 1000 Скачать руководство пользователя страница 5

Safety

WARNING

This product emits small amounts of carbon monoxide (CO) gas which is a harmful, odour-
less gas.  

 directly from the duct during a CO test or within 5 minutes of 

DO NOT INHALE

conducting a CO test

.

Note: Under normal operating conditions, this emission will present no harm to the user. 
For additional information please refer to the separate safety information provided.

CAUTION

This product contains hot surfaces and hot air is also emitted from the duct outlet. 
 

 the tip of the CO capsule when it has been removed if the unit has been 

DO NOT TOUCH

in operation within the previous 5 minutes. It will be very hot immediately after use and may 
burn if touched.

 insert fingers into the aperture from where the CO capsule has been removed.  

DO NOT

There are very hot surfaces which may burn if touched. 
 
Avoid placing hands near the duct outlet during heat testing or within 5 minutes of 
conducting heat testing.
  
Hot air is emitted from the duct and the top of the duct will get hot to the touch.

CAUTION

This product is intended to be used at height.

Exercise great care and always wear appropriate PPE (personal protective equipment) when 
operating above head height in order to avoid the risk of injury.

. Keep proper footing and balance at all times. Proper footing and 

DO NOT OVER REACH

balance enables better control of the equipment in unexpected situations.

Pay particular attention to avoid contact with overhead items such as light fittings, overhead 
power cables/busbars and any other objects that could be accidentally dislodged which 
might cause danger to the operator or anyone else in the vicinity.

General Safety Information

M U L T I - S T I M U L U S   D E T E C T O R  T E S T E R

testifire

®

iv

www.

testifire

.com

Содержание Testifire 1000












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды