Det-Tronics GT3000 Series страница 6 Скачать руководство пользователя

Страница: 6 / 33

12.4

95-8616

SPECIFICATIONS

SENSOR AND TRANSMITTER

AVAILABLE SENSORS—

Refer to Appendix E.

CROSS SENSITIVITY—

See Appendix E for Cross Sensitivity information.

CALIBRATION—

Sensors are calibrated at the factory. Gas type and

range are read by the transmitter. Field calibration is

initiated at the detector, at the UD10/UD20 Universal

Display Unit, or by some other HART interface device.

NOTE: Calibration cannot be initiated via the UD30.

OPERATING VOLTAGE—

24 volts dc nominal. (12 Vdc minimum, 30 Vdc maximum).

Maximum ripple is 2 volts peak-to-peak.

If using the HART function, the installation must comply

with the HART power standard.

POWER CONSUMPTION—

0.8 watt maximum @ 30 Vdc.

CURRENT OUTPUT—

• 4–20 mA (Normal operating mode).
• 3.8 mA indicates calibrate mode.
• 3.5 mA or less indicates a fault condition (2.45 mA

option available).

MAXIMUM LOOP RESISTANCE—

300 ohms at 18 Vdc, 600 ohms at 24 Vdc.

WIRING—

The transmitter has flying leads, 20” long, 600V insulation.
Colors: Red = V+

Black = V–

Green = earth ground

Gauge: 22 AWG (red and black)

16 AWG (green).

WARM-UP—

Warm-up time can last up to 150 seconds.

OPERATING TEMPERATURE—

See Appendix E.

STORAGE TEMPERATURE—

Transmitter: –55°C to +75°C / –67°F to +167°F.

Sensor:

0°C to +20°C / +32°F to +68°F.

Ideal: +4°C to +10°C / +39°F to +50°F.

EXPECTED STORAGE LIFE—

6 months in factory-sealed packaging

HUMIDITY RANGE—

15 to 90% RH.

PRESSURE RANGE—

Atmospheric ±10%.

INGRESS PROTECTION—

IP66.

THREAD OPTIONS—

3/4" NPT or M25.

ENCLOSURE MATERIAL—

GTX Transmitter:

316 Stainless Steel

GTS Sensor Module: PPA (30% carbon filled).

DIMENSIONS—

See Figure 4.

EXPECTED OPERATING LIFE—

2 years in an open air environment.

WARRANTY—(For the GTX and GTS)

12 months from date of installation or 18 months from

date of shipment, whichever occurs first.

CERTIFICATIONS—

For complete approval details, refer to the appropriate

Appendix:

Appendix A - FM

Appendix B - CSA

Appendix C - IECEx

Appendix D - Other Approvals

Figure 4—Dimensions of GT3000 Gas Detector in Inches (CM)

2.5

(6.4)

6.2

(15.8)

5.6

(14.3)

B2397

APPROVED

Содержание GT3000 Series


































Результаты поиска

Содержание GT3000 Series

Отзывы:

Похожие инструкции для GT3000 Series

Бренды по названию

Популярные бренды

Det-Tronics GT3000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание GT3000 Series

Отзывы:

Похожие инструкции для GT3000 Series

Бренды по названию

Популярные бренды