Desmi ESLHT/-17 W180 Скачать руководство пользователя страница 18

 

_______________________________________________________________________________ 

DESMI Pumping Technology A/S 

 

18

 

www.desmi.com

 

Tagholm 1 
9400 Nørresundby 

 Denmark 

Tel: +45 96 32 81 11 Fax: +45 98 17 54 99 
E-mail

[email protected]

 

 

14.

 

EU

 

DECLARATION

 

OF

 

CONFORMITY 

 

DESMI Pumping Technology A/S, hereby declare that our pumps of the ESLV and ESLH and 
ESLHT  type  are  manufactured  in  conformity  with  the  following  essential  safety  and  health 
requirements in the COUNCIL DIRECTIVE 2006/42/EC on machines, Annex 1. 
 
The following harmonized standards have been used: 
 

EN/ISO 13857:2008 

Safety of  machinery. Safety  distances to prevent 
danger zones being reached by the upper limbs 

EN 809:1998 + A1:2009                   

Pumps  and  pump  units  for  liquids 

–  Common 

safety requirements 

EN12162:2001+A1:2009 

Liquid pumps 

– Safety requirements – Procedure 

for hydrostatic testing 

EN 60204-1:2006/A1:2009   

Safety  of  machinery 

–  Electrical  equipment  of 

machines (item 4, General   requirements) 

Ecodesign Directive (2009/125/EC) 

Water pumps: 
Commission Regulation No 547/2012. 
Applies only to water pumps marked with the 
minimum efficiency 
index MEI. See pump nameplate. 

 
Pumps  delivered  by  us  connected  with  prime  movers  are  CE-marked  and  comply  with  the 
above requirements. 
 
Pumps delivered by us without prime movers (as partly completed machinery) must only be 
used when the prime mover and the connection between prime mover and pump comply with 
the above requirements. 
 
 
 
 
Nørresundby, March 05 2019 

 
 
 
 
 
 
 

 
Henrik Mørkholt Sørensen 
Managing Director 
 
DESMI Pumping Technology A/S 
Tagholm 1 
9400 Nørresundby 
 
 
 
 
 
 

 

Содержание ESLHT/-17 W180





















Отзывы: