Desert Aire CM35xx Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 12

Desert Aire CM35xx Скачать руководство пользователя страница 6

6

Pull the cord and connector through the hole in the back of the mounting bracket.

Attach the bracket to the wall. After plugging the cord into the back of the RDT, feed

any extra wiring back into the hole of the mounting bracket and gently snap the RDT

into the bracket.

CAUTION: Do not run the remote terminal wiring in the same conduit as,

or adjacent to wires carrying over 30 volts!

3. General

Instructions

Figure 1

The controller is pre-programmed and conﬁ gured at the factory for use in the application you

have speciﬁ ed. The RDT, Figure 1, allows the operator to monitor the operation and adjust the

setpoints of the Desert Aire dehumidiﬁ er. The RDT has an LCD screen and 6 keys. The keys

on the left hand side of the RDT, top to bottom, are the ALARM key shown as an alarm bell,

PROGRAM key abbreviated “Prg” and the ESCAPE key abbreviated “Esc.” The keys on the

right hand side of the RDT, top to bottom, are the UP key shown as an up arrow, the ENTER

key shown as a left arrow and the DOWN key shown as a down arrow.

Desert Aire - CM35xx Quick Start Guide

«
...
4
5
6
7
8
...
»

Содержание CM35xx













Отзывы:

Нет отзывов