background image

TB-3073

 Page 7 of 7

© 2017 DESCO INDUSTRIES, INC.

Employee Owned

DESCO WEST 

- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178

DESCO EAST 

- One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: 

Desco.com

Specifications

Input Voltage and 

Frequency

(External Adapter)

AC/DC Power Adapter
Power Input: 

100-240VAC, 50/60 Hz
Power Output: 

24VDC @ 150mA
Cable Length: 

5 ft. (1.5 m)

Operating Temperature 50 to 95°F (10 to 35°C)
Environmental 

Requirements

Indoor use only at altitudes 

less than 6500 ft. (2 km)
Maximum relative humidity 

of 80% up to 85°F (30°C) 

decreasing linearly to 50% @ 

85°F (30°C)

Dimensions 

(Monitor)

3.87" L x 2.09" W x .90" H

(98 mm x 53 mm x 23 mm)

Dimensions 

(Remote Alarm)

1.78" L x 1.08" W x .79" H

(45 mm x 27 mm x 20 mm)

Weight

(Monitor)

0.14 lbs. (0.06 kg)

Weight

(Remote Alarm)

0.02 lbs. (0.01 kg)

Operator Test Range* 500 kilohms to 10 megohms 

impedance

Worksurface Test 

Limit**

10 megohms (±10%)

Operator Test Voltage 1.2V peak-to-peak @ 1.2µA, 

open circuit

Worksurface Test 

Voltage

5 to 7.5V, open circuit

Alarm Response Time <50 ms
Country of Origin

United States of America

*This cannot be verified with standard DC test 

equipment. The continuous monitor is an impedance 

sensing device, and the limits are determined by the 

magnitude and angle of the impedance.
**The worksurface mat must have a conductive 

layer such as Dual Layer Rubber or Dissipative 

3-Layer Vinyl with conductive buried layers. Desco 

workstation monitors are not recommended for use with 

homogeneous matting.

Limited Warranty, Warranty Exclusions, Limit 

of Liability and RMA Request Instructions

See the Desco Warranty - 

http://desco.descoindustries.com/Limited-Warranty.aspx

Содержание 19651








Отзывы: