TB-2039
Page 4 of 4
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 • Fax (909) 627-7449
DESCO EAST
- 90 Hudson Road, Canton, MA 02021-1407 • (781) 821-8370 • Fax (781) 575-0172 • Web Site: http://www.desco.com
Limited Warranty
Desco expressly warrants that for a period of one (1) year from
the date of purchase, Desco Calibration Units will be free of
defects in material (parts) and workmanship (labor). Within the
warranty period, the product will be tested, repaired, or replaced
at Desco’s option, free of charge. Call our Customer Service
Department at 909-627-8178 (Chino, CA) or 781- 821-8370
(Canton, MA) for a Return Material Authorization (RMA) and
proper shipping instructions and address. Include a copy of your
original packing slip, invoice, or other proof of purchase date.
Any unit under warranty should be shipped prepaid to the Desco
factory. Warranty repairs will take approximately two weeks.
If your unit is out of warranty, call Customer Service at 909-627-
8178 (Chino, CA) or 781-821-8370 (Canton, MA) for a Return
Material Authorization (RMA) and proper shipping instructions
and address. Desco will quote repair charges necessary to
bring your unit up to factory standards.
Warranty Exclusions
THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU
OF ALL OTHER PRODUCT WARRANTIES, EXPRESSED AND
IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY
DISCLAIMED. The express warranty will not apply to defects or
damage due to accidents, neglect, misuse, alterations, operator
error, or failure to properly maintain, clean or repair products.
Limit of Liability
In no event will Desco or any seller be responsible or liable for
any injury, loss or damage, direct or consequential, arising out of
the use of or the inability to use the product. Before using,
users shall determine the suitability of the product for their
intended use, and users assume all risk and liability whatsoever
in connection therewith.
Resistance Value
Test Output - LED
Red jack “A” - 675K:
Red (Low-hazard)
Green jack “B” - 825K:
Green (OK-in limits)
Green jack “C” - 80M:
Green (OK-in limits)
Yellow jack “D” - 120M:
Red (High resistance)
Step 3:
Repeat the procedure testing across jacks B,
C (80M), and D (120M). The different resistance
ranges should give the display shown above. If the
tester does not meet calibration specifications, contact
factory for calibration, or ask for Technical Bulletin
TB-2040.
Figure 9. Testing 19250 for “PASS” and “FAIL” ranges
for footwear circuit as indicated on calibration unit.
Specifications
Power Source:
Passive device, no power source
required
Resistance Ranges -
Wrist straps:
Low -
675 Kilohm
Pass -
825 Kilohm
Pass -
8.5 Megohm
High -
11.5 Megohm
Footwear:
Low -
675 Kilohm
Pass -
825 Kilohm
Pass -
80 Megohm
High -
120 Megohm
Calibration:
NIST traceable
Calibration Interval:
Recommended annually
Accuracy:
±2%
Weight:
10 ounces
Dimensions:
4.50" x 3.25" x 1.00"
Consider adding the 07010 to your list of “test
equipment that shall be selected to make
measurements of appropriate properties of the
technical requirements that are incorporated into the
ESD program plan” as required by paragraph 6.1.3.1 of
ANSI/ESD S20.20.
© 2003 DESCO INDUSTRIES INC.
Employee Owned
