background image

www.desatech.com

110112-01C

22

Automatic Ignitor 
Electrode

Pilot Burner

Figure 38 - Pilot (Propane/LP Gas 

Shown)

Manual 
Ignitor
Electrode

Thermocouple

OPERATING FIREPLACE

Continued

B.  Using Hand-Held Wireless Remote 
Control

1.  Set  manual  ignition  bypass  switch  on 

control panel to OFF position (automatic 

ignition position).

2.  Wait five (5) minutes to clear out any gas. 

Smell for gas around heater and near floor. 

If you smell gas, STOP! Follow “B” in the 

safety information on warnings plate. If you 

donʼt smell gas, go to the next step.

3.  Point  remote  control  toward  the  lower 

front of fireplace and push both buttons at 

the same time. Hold for 6 seconds. The gas 

valve will open and electronic ignition will 

begin sparking to light the pilot. 

Note:

 You 

will be able to hear a clicking sound during 

this process. LED on wall switch will light.

 

Note:

 You may be running this heater for 

the first time after connecting to gas supply 

or at the start of your heating season. If so, 

the ON button may need to be pressed again. 

This will allow air to bleed from gas system. 

If several attempts to light pilot fail, contact 

a qualified service person or gas supplier 

for repairs. Until repairs are made, light 

and operate manually (see 

Manual Lighting 

Instructions for Electrical Power Outage

).

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater - Wall Switch

Push ON/OFF button on wall switch once.

Shutting Off Heater - Wireless Remote 
Control

Point remote control toward lower front of fire-

place and push both buttons at the same time.

MANUAL LIGHTING

INSTRUCTIONS FOR 

ELECTRICAL POWER 

OUTAGE

 WARNING: You must oper-

ate this heater with the fireplace 

screen in place. Make sure fire-

place screen is in place before 

running heater. 

NOTICE: During initial operation of 

new heater, burning logs will give 

off a paper-burning smell. Open 

damper or window to vent smell. 

This will only last a few hours. 

Because this fireplace has an electronic ignition 

system, in the event there is a loss of power, it 

will be necessary to manually light the pilot with 

the piezo ignitor. After the pilot is lit, the main 

burner will light automatically.

1.  Follow steps 1 through 3 under 

Normal 

Lighting Instructions

, page 21.

2.  Set manual ignition bypass switch on con-

trol panel to ON position (manual ignition 

position). See Figure 39, page 23.

3.  The pilot is attached to the rear of the front 

burner. You will be able to see the pilot 

and spark electrode without removing the 

screen or logs.

Manual 
Ignition 
Bypass 
Switch 
(Up is for 
Remote 
Control)

ON/OFF 
Button

HI/LO 
Button

Wall Switch 
Assembly

Figure 37 - Control Locations

LED

4.  When pilot flame is lit, the thermocouple is 

heated by the flame. When thermocouple 

becomes hot (5 to 15 seconds), main burner 

will automatically light on high flame.

5.  To lower flame, point remote control toward 

lower front of fireplace and push HI/LO 

button once.

 

Note:

 This fireplace does not have a pilot-

only mode.

Содержание VTGF33NRA









































Отзывы: