Desa Vanguard VMH26TNC Скачать руководство пользователя

Страница: 30 / 32

www.desatech.com

113111-01D

ACCESSORIES

NOTICE: All accessories may

not be available for all ﬁreplace

models.

Purchase these ﬁreplace accessories from your lo-

cal dealer. If they cannot supply these accessories

call DESA Heating Productsʼ Sales Department at

1-866-672-6040 for referral information. You can

also write to the address listed on the back page

of this manual.

EQUIPMENT SHUTOFF VALVE
GA5010

For all models.

Equipment shutoff valve with

1/8" NPT tap.

PERIMETER TRIM KIT - GA6095

For all models.

Optional four-sided perimeter trim

kit for custom and recessed installations (when unit

is on the ﬂoor). Provides a ﬁnished appearance by

covering rough edges of wall opening.

PERIMETER TRIM KIT

GA6094 - Polished Brass
GAB6094 - Black
GAP6094 - Platinum

For all models.

Optional three-sided perimeter

trim kit for custom and recessed installations

(when unit is on the ﬂoor). Provides a ﬁnished ap-

pearance by covering rough edges of wall opening.

Black trim included with all mantels.

EXTRUDED LOUVER KIT

(Not Shown)
GA9092 - Polished Brass
GAP9092 - Platinum

For all models.

Optional extruded louver. Kit

contains 2 louvers.

THERMOSTATICALLY -
CONTROLLED BLOWER KIT
GA3450TA

For all models.

Provides better heat distribution.

Makes ﬁreplace more efﬁcient. Automatically

turns off and on as needed.

CORNER MANTEL WITH FULL
HEARTH BASE (Not Shown)

GMC64FC Series - Oak Finished
GMC63UC Series - Unﬁnished
CS26CP Series - 2-Tone Finish

(Black/Lyptus)

GMC83FA Series - Oak Finished

(Column Style)

CMA208F Series - Oak Finished

For all models.

Space-saving mantel and hearth

base corner design features clean, classic lines.

Available in a stained oak, 2-tone ﬁnish or an

unfinished hardwood, ready to stain or paint.

Complete assembly instructions included. Three-

sided perimeter trim kit included.

CABINET MANTEL AND FULL
HEARTH BASE (Not Shown)

GMC80FA Series - Oak Finished

(Column Style)

CMA204F Series - Oak Finished

(Column Style)

CMA205U Series - Unﬁnished

(Column Style)

CMA210W Series - White Lacquer Finished
CMA306F Series - Oak Finished
WS26CP Series - 2-Tone Finish

(Black/Lyptus)

WS26DLS Series - Lyptus Finished
GMC61UC Series - Unﬁnished
GMC60FC Series - Oak Finished

For all models.

Mantel features clean, classic

lines. Available in a stained oak, 2-tone ﬁnish or

an unﬁnished hardwood, ready to stain or paint.

Complete assembly instructions included. Three-

sided perimeter trim kit included.

Содержание Vanguard VMH26TNC

































Результаты поиска

Содержание Vanguard VMH26TNC

Отзывы:

Похожие инструкции для Vanguard VMH26TNC

Бренды по названию

Популярные бренды

Desa Vanguard VMH26TNC, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание Vanguard VMH26TNC

Отзывы:

Похожие инструкции для Vanguard VMH26TNC

Бренды по названию

Популярные бренды