background image

11

104433

OWNER’S MANUAL

Securing Hearth Base to Floor

1.

Position hearth base in desired location.
Mark holes for drilling (see Figure 18).
Remove hearth base.

2.

For carpeted floor, make a small cut with
a sharp knife at marked locations before
drilling. If securing to a wood floor, drill
a 3/4" deep hole using a 1/8" diameter
drill bit. Do not use anchors in wood
floors. If securing to a concrete floor,
drill a 1 

3

/

8

" deep hole using a 1/4" di-

ameter concrete drill bit. Completely
insert anchors into each hole.

3.

Mount heater to hearth base following
steps under Mounting Heater to Op-
tional Hearth Base, 
below. After
mounting heater, position heater and
hearth base over drilled holes. With
slotted screwdriver, secure hearth base
to floor with four wood screws.

Mounting Heater to Optional
Hearth Base

1.

Lay heater on its back on a table with
the bottom of heater overhanging the
edge of the table.

2.

Remove 2 shipping screws in bottom
of heater. Discard shipping screws.

3.

Line up mounting holes on top of hearth
base with holes in bottom of heater (see
Figure 18).

4.

Using a Phillips screwdriver, secure
hearth base to heater with four sheet
metal screws (see Figure 18).

5.

Stand heater up on base.

6.

Place hearth insert in hearth base as
shown in Figure 19.

7.

Assemble brass trim (see steps 1
through 7 under Assembling and At-
taching Brass Trim, 
page 5).

8.

Slide base trim on heater base. Attach
brass trim to base with two brass screws
included as shown in Figure 19.

INSTALLATION

Continued

Figure 19 - Placing Hearth Insert on Heater
Base and Attaching Brass Base Trim

Brass Base
Trim

Figure 18 - Attaching Heater to Hearth
Base

Base

Holes for Securing
Heater to Floor

Shipping
Screw

Bottom of Heater

Hearth
Insert

Laminate
Sheet

Screw

Sheet Metal Screw

Mounting Holes

C. MOUNTING HEATER

 WITH

OPTIONAL HEARTH BASE (IF
APPLICABLE) TO OPTIONAL
MANTEL

See Instructions Included With
Mantel Kit.

Assembling Mantel

IMPORTANT:

 Only use the optional man-

tels specified in this manual. See Accesso-
ries,
 page 21 for proper mantel kits. This
heater is only approved for use with models
GMF800 series / GMU801 series, GM900F
series / GM901U series, GM700F/GM701U
series, GMC22F/GMC23U/GMC24U se-
ries, GMC32F/GMC33U series, GMC34F/
GMC35U series, and GMC26F/GMC27U/
GMC28F series mantel kits. Using any other
mantel will void the CSA/AGA approval
for this heater. Do not use models GMF800/
GMU801 series, GM900F/GM901U series,
GM700F/GM701U series, GMC22F/
GMC23U/GMC24U series, GMC32F/
GMC33U series, GMC26F/GMC27U/
GMC28F series and GMC34F/GMC35U
series mantels with any other product. If the
metal base is required with your mantel, the
heater must be mounted on the base first.

Continued

Содержание Comfort Glow RFN30T

























Отзывы: