background image

www.desatech.com

113896-01D

4

SAFETY INFORMATION

Continued

1.  This appliance is only for use with the type 

of gas indicated on the rating plate. This ap

-

pliance is not convertible for use with other 

gases.

2.  Do not place propane/LP supply tank(s) in

-

side any structure. Locate propane/LP supply 

tank(s) outdoors (propane/LP units only).

3.  If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use 

any phone in your building

• immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions

• if you cannot reach your gas supplier, call 

the fire department

4.  This fireplace shall not be installed in a bed

-

room or bathroom.

5.  Do not use this fireplace as a wood-burning 

fireplace. Use only the logs provided with the 

fireplace. 

6.  Do not add extra logs or ornaments such as 

pine cones, vermiculite or rock wool. Using 

these added items can cause sooting. Do not 

add lava rock around base. Rock and debris 

could fall into the control area of fireplace.

7.  This fireplace is designed to be smokeless. 

If logs ever appear to smoke, turn off fire

-

place and call a qualified service person. 

Note:

 During initial operation, slight smoking 

could occur due to log curing and fireplace 

burning manufacturing residues. 

8.  To prevent the creation of soot, follow the 

instructions in 

Cleaning and Maintenance

page 21.

9.  Before using furniture polish, wax, carpet 

cleaner or similar products, turn heater off. If 

heated, the vapors from these products may 

create a white powder residue within burner 

box or on adjacent walls or furniture.

10.  This fireplace needs fresh air ventilation to run 

properly. This fireplace has an Oxygen Deple

-

tion Sensing (ODS) safety shutoff system. The 

ODS shuts down the fireplace if not enough 

fresh air is available. See 

Air for Combustion 

and Ventilation

, page 5. If fireplace keeps 

shutting off, see 

Troubleshooting

, page 22.

11.  Do not run fireplace

• where flammable liquids or vapors are used 

or stored.

• under dusty conditions.

12.  Do not use this fireplace to cook food or to 

burn paper or other solid fuels.

13.  Do not use fireplace if any part has been under 

water. Immediately call a qualified service 

technician to inspect the room fireplace and 

to replace any part of the control system and 

any gas control which has been under water. 

14.  Turn off and unplug fireplace and let cool 

before servicing. Only a qualified service 

person should service and repair fireplace.

15.  Operating fireplace above elevations of 4,500 

feet could cause pilot outage.

16.  Do not operate fireplace if any log is broken. 

Do not operate fireplace if a log is chipped 

(dime-sized or larger).

17.  To prevent performance problems, do not use 

propane/LP fuel tank of less than 100 lbs. 

capacity (propane/LP units only).

18.  Provide  adequate  clearances  around  air 

openings.

LOCAL CODES

Install and use fireplace with care. Follow all local 

codes. In the absence of local codes, use the lat

-

est edition of 

The National Fuel Gas Code, ANSI 

Z223.1/NFPA 54

*.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY  10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA  02269

UNPACkING

1.  Remove fireplace from carton.

2.  Remove all protective packaging applied to 

fireplace for shipment.

3.  Make sure your fireplace includes one hard

-

ware packet. 

4.  Check fireplace for any shipping damage. If 

fireplace is damaged, promptly inform dealer 

where you bought fireplace.

f i r e - p a r t s . c o m

Содержание Comfort Glow CF26NTA

































Отзывы: