Desa ARL B50H Скачать руководство пользователя

Страница: 9 / 16

102553

Pump Pressure
Adjustment

1. Remove pressure gauge plug from

filter end cover.

2. Install accessory pressure gauge

(part number HA1180).

3. Start heater (see Operation, page 5).

Allow motor to reach full speed.

4. Using a flat blade screwdriver, set

the pressure to 3.6 PSI. Turn relief
valve to right to increase the
pressure. Turn relief valve to left to
decrease the pressure.

5. Remove pressure gauge. Replace

pressure gauge plug in filter end
cover.

Figure 6 - Pressure Gauge Plug Removal

Relief
Valve

Pressure
Gauge
Plug

Figure 7 - Adjusting Pump Pressure

Pressure
Gauge

Fuel Filter

1. Remove 4 side cover screws using

5/16" nut-driver.

2. Remove side cover.
3. Pull upper fuel line off fuel filter

neck.

4. Carefully pry bushing and fuel

filter out of fuel tank.

5. Wash fuel filter with clean fuel and

replace in tank.

6. Attach upper fuel line to fuel filter

neck.

7. Replace side cover.

Fuel Filter

Side Cover

Upper Fuel Line

Figure 8 - Fuel Filter Removal

Содержание ARL B50H

















Результаты поиска

Содержание ARL B50H

Отзывы:

Похожие инструкции для ARL B50H

Бренды по названию

Популярные бренды

Desa ARL B50H, Руководство пользователя

Результаты поиска

Содержание ARL B50H

Отзывы:

Похожие инструкции для ARL B50H

Бренды по названию

Популярные бренды