DERRICK EX Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 38

DERRICK EX Скачать руководство пользователя страница 8

EX, SGX VIBRATOR MOTORS

REPAIR RESTRICTIONS

The Derrick EX and SGX motors have a CLASS I (flammable gas atmosphere) certification, which
restricts the user to replacing only the following parts:



Bearings



Outer eccentric weights



Power

cord



Junction box components

To maintain the flameproof rating of the motor, no parts beyond the bearing may be removed.

Also, while under warranty, no repairs of any kind are permitted; the motor may not be opened for
any reason. If the motor fails while under warranty, contact the Derrick Service department for
assistance. The warranty will be void, if it is determined that the motor has been opened during
the warranty period.

Caution! Contact The Derrick Service Department If Motor Fails During The
Warranty Period. All Warranties, Whether Stated Or Implied, Will Be Null And
Void If The Motor Is Opened During The Warranty Period. Derrick Corporation
May Not Be Held Responsible For Any Liabilities Incurred During, Or As A
Result Of, Unauthorized Repair Attempts.

SAFETY

Successful and safe operation of Derrick vibrator motors requires proper handling, installation,
operation, and maintenance. Failure to follow installation and maintenance requirements may
result in personal injury, equipment failure, or property damage.

Only

trained, qualified personnel

should be involved in the installation, operation, and

maintenance procedures.

All plant safety procedures must be observed.

Qualified personnel must be familiar with the construction, installation, maintenance, and
operation of the motor and must be aware of any hazards associated with operation of the
equipment. In addition, personnel must be trained and authorized to energize, de-energize, clear,
ground, and tag circuits and equipment in accordance with established safety practices and be
trained in proper use and care of personal protective equipment in accordance with established
safety practices.

WARNING! ALL DERRICK VIBRATOR MOTORS MUST BE INSTALLED AND
GROUNDED IN ACCORDANCE WITH ALL APPLICABLE ELECTRICAL CODES.

WARNING! TO AVOID SERIOUS PERSONAL INJURY, BE SURE THAT
EQUIPMENT IS LOCKED OUT, TAGGED OUT, AND DE-ENERGIZED BEFORE
PERFORMING MAINTENANCE AND/OR ADJUSTMENTS.

WARNING! MOTOR HOUSING BECOMES HOT DURING OPERATION AND MAY
CAUSE SEVERE BURNS. DO NOT TOUCH MOTOR HOUSING DURING OR
IMMEDIATELY AFTER MOTOR HAS BEEN OPERATING.

2

01 May 09

«
...
6
7
8
9
10
...
»

Содержание EX







































Отзывы:

Нет отзывов