background image

Shenzhen Dericam Technology Co.,LTD 

   

                                                           H501W User Manual 

www.dericam.net

           Copyright @ Shenzhen Dericam Technology Co., Limited                    

[email protected]

 
 

16

5.12  Mail Service Settings 

 

Fig5.12 

Mail Service Settings 

1------Sender               Email address to be used as a sender 

2------Receiver 1 to 3                Email address to be used as a receiver, up to four receivers 

3------SMTP Server          SMTP Server of the Sender mailbox 

4------SMTP Port                        SMTP port no. of the mail server of the sender mailbox 

5------SMTP User           ID Account of the sender email address 

6------SMTP Password       The password of the sender email address 

Trouble Shooting----The email failed to send emails or snapshots 

1. Check the mail service settings, and make sure all of them are correct and try it again. 

2. Check if the sender email is enabled with SMTP server. 

5.13  FTP Service Settings 

 

Fig5.13

 FTP Service Settings

 

In order to use FTP function, user should apply user name and password on the FTP server first. And please apply 

for storage right, in order to write and create sub-category on the FTP server. 

Содержание H501W




















Отзывы: