Derbi Dirtboy 10 Скачать руководство пользователя страница 44

Страница: 44 / 48

UBRICATION

CRANKSHAFT OIL SEALS

Removal

- Extract the flywheel-side oil seal from the crank- case
taking care not to damage or score the crankcase.

- Pour engine oil over the oil seal and its seat in the
crankcase.

- Operating from the outside with the specific drift, push the
oil seal fully home into its seat in the crankcase.

Specific tooling

020340Y Flywheel-side oil seal fitting drift Oil pump

PUMP

INSPECTION

- Remove the two oil pump fixing screws.

- Remove the inner rotor circlip.

- Remove the rotors and carefully clean them with a
degreasing solvent and compressed air.

- Refit the two impellers with pump body and install the
circlip.
Using a thickness gauge, measure the distance between the
rotors (inner rotor - outer rotor) at the position shown in the
figure.

HARACTERISTIC

Maximum allowable clearance:

0,15

ENGINE

- OIL PUMP

ENGINE

- OIL PUMP

UBRICATION

Содержание Dirtboy 10

















































Результаты поиска

Содержание Dirtboy 10

Отзывы:

Похожие инструкции для Dirtboy 10

Бренды по названию

Популярные бренды

Derbi Dirtboy 10, Руководство по ремонту

Результаты поиска

Содержание Dirtboy 10

Отзывы:

Похожие инструкции для Dirtboy 10

Бренды по названию

Популярные бренды