Denzel 26915 Скачать руководство пользователя страница 7

7

ANGLE GRINDER 

EN

c)  Abrasive tools may only be used for their intended purpose. Never sand by the side of the cutting disc. Cutting 

discs are designed for cutting material by edge. Other use of the circle may lead to its destruction and injury. 

Additional special warnings instructions for grinding and cutting 

a)  Prevent blocking of the cutting wheel, do not exceed the pressing force. Do not perform too deep cuts. 

Overload of the cutting wheel increases the probable tilting or blocking and this increases the risk of a kickback 
or a tooling break.

b)  Be especially careful when cutting with a cutting wheel in the direction away from you. In case of a back kick 

power tools with a spinning circle can bounce right at you.

c)  When jamming the cutting wheel turn off the electric tool and hold it until the wheel stops. Never try to remove 

the rotating cutting wheel from the cut, as this may cause a back kick. Establish and eliminate the cause 
of jamming.

d)  Do not turn the electric tool on again, if the tooling is in the workpiece. Let the cutting wheel develop the full 

speed, before you continue cutting carefully. Otherwise, the disc may jam which will cause a kickback.

e)  Plates or large workpieces must lie securely on the support to reduce the risk of jamming of the cutting disc. 

Consider that large workpieces can sag under their own weight. 

Special warnings when sanding 

Do not use oversized sanding sheets, and follow the manufacturer's specifications for sanding sheets. Sanding 
sheets protruding over the edge of the sanding pad can cause injury and blockage, tear or cause kickback.

Special warnings for working with wire brushes 

a)  Keep in mind that wire brushes lose elements during normal operation. Do not overload the brushes with 

excessive pressing force. Flying pieces of wire can easily penetrate clothing and injure the operator. 

b)  If for work it is recommended to use a wheel protective cover, then exclude the contact of the wire brush 

with the casing. Consider that dish and cup brushes can increase its diameter while rotation under the action 
of centrifugal forces.

Residual risks

In spite of the compliance with relevant security means instructions and use of safety devices, some residual 
risks cannot be completely eliminated. They are:

• 

Injuries caused by touching hot or rotating tool parts or workpiece.

• 

The possibility of ignition of some materials under the influence of sparks when grinding.

• 

Impairment of hearing.

• 

Risk of pinching fingers when changing working tool.

• 

Damage to health due to vibration appearing at.

• 

Damage to health due to inhalation of dust when working with stone, concrete and bricks.

• 

Damage to health due to long observation of sparks generated by grinding. 

Содержание 26915

































Отзывы: