manualshive.com logo in svg

Denyo DCA-10LSX, Инструкция по эксплуатации

Поделиться
Скачать
Denyo DCA-10LSX Скачать руководство пользователя страница 17

Indication/alarm lamp

(1)  Preheat lamp

When the starter switch is set in the  "PREHEAT" position, 

this lamp goes on.
In a little time this lamp goes off, indicating that the machine 

has been preheated to be ready for startup.

(2) Warning Lamps

This monitor indicates the following failures, if any one of 
them occurs.

ф   High jacket water temperature
This  lamp goes on when the water temperature rises

abnormally.
If this lamp goes on during operation, the emergency stop 
device immediately operates to shut down the engine 
automatically.

(2)  Oil pressure failure

If this machine is in normal operation, this lamp stays off. 

When the starter switch is turned to  "RUN" position to start 

the engine, the lamp goes on, and when the oil pressure rises 

after startup, it goes off.

If this lamp goes on during operation, the emergency stop 
device immediately operates to shutdown the engine 
automatically.

©   Insufficient charge
This lamp goes on when the output voltage of the alternator 

drops unusual value.
If this lamp goes on during operation, the emergency stop 

device immediately operates to shutdown the engine 
automatically.

13

Содержание DCA-10LSX

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды