Dentsply Sirona CEREC Zirconia meso Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 26

Dentsply Sirona CEREC Zirconia meso Скачать руководство пользователя страница 4

1 Introduction
1.1 Dear Customer,

Dentsply Sirona

Processing instructions CEREC Zirconia meso

4

66 21 101 D3487

D3487.201.18.02.02 02.2018

1

Introduction

1.1

Dear Customer,

Thank you for purchasing the Dentsply Sirona product CEREC Zirconia
meso.

CEREC Zirconia meso blocks are intended for use in manufacturing
individually designed, directly screw-retained crowns and partially
reduced, directly screw-retained crowns, which are glued to a fitting
titanium base after milling/grinding and sintering.

Improper use and handling can create hazards and cause damage.
Please therefore read and follow these operating instructions carefully.
Always keep them within easy reach.

Also pay attention to the safety instructions in this document to prevent
personal injury and material damage.

Please also observe the instructions provided by the manufacturer of
the titanium base or the implant.

Your

CEREC Consumables Team

1.2

Contact information

Manufacturer's address

Sirona Dental Systems GmbH
Fabrikstrasse 31
64625 Bensheim
Germany

Tel.: +49 (0) 6251/16-0
Fax: +49 (0) 6251/16-2591
e-Mail:

[email protected]

www.dentsplysirona.com

1.3

Copyright

© Sirona Dental Systems GmbH. All rights reserved.

«
...
2
3
4
5
6
...
»

Содержание CEREC Zirconia meso



























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды