Denon DVP-602CI, Руководство по обслуживанию

Страница: 25 / 87

25
DVP-602CI
71 P21/AN21/A1 - O C − − Ed Z O/L O/L −
72 P20/AN20/A0 - O C − − Ed Z O/L O/L −
73 P17/INT5/D15 PROTECTION I C Lv 5V Eu Z I I PROTECTION detect pin
74 P16/INT4/D14 ERESET O − − 3.3V Ed Z O/L O/L ETHERNET comm. control pin
75 P15/INT3/D13 REMOTEDET I − E ↓ &H 5V − Z I I ROOM TO ROOM Signal detect pin (Detected : H)
76 P14/D12 - I − − − Ed Z O/L O/L −
77 P13/D11 - I − − − Ed Z O/L O/L −
78 P12/D10 - I C − − Ed Z O/L O/L −
79 P11/D9 - I C − − Ed Z O/L O/L −
80 P10/D8 - I C − − Ed Z O/L O/L −
81 P07/AN07/D7 - I C − − Ed Z O/L O/L −
82 P06/AN06/D6 - I − − − Ed Z O/L O/L −
83 P05/AN05/D5 - I C − − Ed Z O/L O/L −
84 P04/AN04/D4 - I C − − Ed Z O/L O/L −
85 P03/AN03/D3 FL̲CLK O C − 5V − Z O/L O/L FL DRIVER control pin
86 P02/AN02/D2 FL̲DATA O C − 5V − Z O/L O/L FL DRIVER control pin
87 P01/AN01/D1 FL̲CE1 O C − 5V − Z O/L O/L FL DRIVER control pin
88 P00/AN00/D0 FL̲RST O C − 5V − Z O/L O/L FL DRIVER control pin
89 P107/AN7/KI3 - I − − − Ed Z O/L O/L −
90 P106/AN6/KI2 GRNLED O − − 5V Ed Z O/L O/H POWER/STANDBY LED control pin (ON : H)
91 P105/AN5/KI1 REDLED O C − 5V Ed Z O/L O/H POWER/STANDBY LED control pin (ON : H)
92 P104/AN4/KI0 - I C E ↓ &H 5V Eu Z I I −
93 P103/AN3 KEY3 I − Lv 5V Eu Z O/L O/L Button input3
94 P102/AN2 KEY2 I − Lv 5V Eu Z O/L O/L Button input2
95 P101/AN1 KEY1 I − Lv 5V Eu Z O/L O/L Button input1
96 AVSS AVSS − − − − − − − − AVSS
97 P100/AN0 MODE I − Lv 5V − Z I O/L Destination switching input
98 VREF MASTER5V − − − 5V − − − − Ref. power supply input +5V
99 AVCC AVCC − − − − − − − − AVCC
100 P97/ADTRG/RXD4 RSTSUB O − − 5V Ed Z O/L O/L SUB-μcom reset output
Pin Pin Name Symbol I/O Type Det VCC Op(Ext.) Res STBY stop Function
Note: Pin No. : Terminal number of microcomputer.
Port Name : The name entered in the data sheet of microcomputer.
Symbol
: Symbolized interface function.
I/O : Input or out of part.
“I” = Input port
“O” = Output port
Type : Composition of port in case of output port.
“C” = CMOS output
“N” = NMOS open drain output
“P” = PMOS open drain output
Op : Pull up/Pull down selection information.
“Iu” = Inner microcomputer pull up
“Id” = Inner microcomputer pull down
“Eu” = External microcomputer pull up
“Ed” = External microcomputer pull down
Det : Indicates judging state of input port. Level detection is “LV”; Edge detection is “Ed”; Detection by both shifting is “E&L”;
Serial data detection is “S” (Serial data output is also “S”).
Res : State at reset.
“H” = Outputs High Level at reset
“L” = Outputs Low Level at reset
“Z” = Becomes High impedance mode at reset
STBY : State of port when STANDBY mode.
“O/L” = Output port and “L”
“I”
= Input port
Stop : State of port when Stop mode.
“O/L” = Output port and “L”
“I”
= Input port