background image

15

ENGLISH

Clearing all data

7

Press the FLIP button for at least 2 seconds.

FLIP

LOOP

• All data is cleared when the the flip button is held down

for 2 seconds.

Off

NOTE:

• When A-1 or A-2 is cleared during seamless looping, it may

take about 2 seconds before A-1 or A-2 can be set again.

Clearing the A-B seamless loop

6

While holding down the FLIP button, press the A button you
want to clear (A-1 or A-2) for at least 2 seconds.

1

2

A

FLIP

A2  B

A1  B

1

2

• The A-1 point (or A-2 point) and the B point are cleared.

Off

Off

or

Off

Off

or

NOTE:

• When the disc tray is opened, the start (A) and end (B) point

settings are cleared.

Hot Starts

Hot starting is possible during a seamless loop or even without a B

point being set.

1

With the data for A-1 or A-2 loaded, press the A-1 (or A-2)
button to hot start.
• Playback starts immediately from the start point (A) when

the button is pressed.

• The A-1 or A-2 points can be set in advance so that in

front of a live audience, you are able to jump from A to A
on the fly. (slam-mix)

“H/S” is displayed once a hot start has been loaded.

While data is loading, hot start is only possible for that
point (A-*)

Fine-adjusting the start points (A-1 and A-2) and
end point (B)

1

2

3

Adjust the start point (A).

To fine-adjust the position of the A-1 (or A-2) point once it
has been set, in the standby mode press and hold down the
CUE button then push the “A” button that you wish to edit.

Use the Jog/Shuttle wheel to manualy search through the
track in order to find your desired new start point. When
found, press the same “A” button to resave.

Adjust the end point (B).

Follow the same steps from 1 & 2 above, except, press and
hold the CUE button and then the B button in order to edit
your end B point, Then press the B button again to save
your changes.

CUE

CUE

1

2

A

A1  

SEARCH

SCAN

I

I

I

LOADING

• The stanby mode is now set to edit/fix either A-1 or A-2

points.

The A-1, A-2 and B points can also be adjusted in the standby

mode at their respective points.

NOTE:

• It is not possible to set an A point at a position after the B

point or the B point at a position before the A point.

” indicator will flashed.

LOADING

Flashing

Flashing

Содержание DN-2100F





















Отзывы: