manualshive.com logo in svg

Denison Hydraulics Goldcup 24, Информация о сервисе

Поделиться
Скачать
Denison Hydraulics Goldcup 24 Скачать руководство пользователя страница 13

UNIT DISASSEMBLY

12

NOTE:

This is a complete vane cartridge assembly and removed in one step. A puller

tool 

T3

is recommended.

Remove sealing washer (1).

See figure 4.

Remove holddown lock retainer ring (8). (Use internal snap ring pliers.)

See figure 9.

Remove four screws (1) and two screws (8).

NOTE:

There is a preload

from the barrel holddown which will lift the por t block approximately 1/8” (3.2mm) at
release.

Carefully lift and remove port block (2) and port plate (4).

CAUTION:

The port plate

may cling to the barrel face because of oil film. Do not allow the port plate to fall and
become damaged.

See figure 6.

Remove the face plate (2) and face plate pins (1) from the face of the

barrel assembly.

See figure 4.

Remove holddown adjusting screw lock (7), use an 18” blade type

screwdriver, with the blade ground down to clear holddown shaft.

See figure 7.

Lock main shaft from turning.

See figure 4.

Use special tool 

T2

, slip over auxiliary shaft (2) and engage dowels into

holddown adjusting screw (6). Loosen load but do not remove.

See figure 6.

Remove two bolts (5) holding housing and flange together .

See figure 3.

Push tubes (4) out of housing slots and to ward barrel, do not bend or

damage them.

See figure 6.

Lift housing (4) over tubes and barrel assembly and remove. Mounting

flange must be driven from housing due to tight fit.

NOTE:

Do not damage gasket faces in this process. Do not remove the retaining

screws or bearing from the housing unless bear ing is damaged and replacement is
necessary.

Barrel assembly can be removed by lifting with auxiliary shaft. The pistons will remain
with the cam assembly. These parts are precision finished and must be handled with
extreme care!

See figure 4.

Using special tool 

T2

, holddown assembly can be removed from barrel.

Remove adjusting screw, (6), spring (5), retainer (4), spherical seat (3) and auxiliary
shaft (2).

See figure 9.

Remove four screws (1) and two screws (8).

NOTE:

There is a preload

from the barrel holddown which will lift the por t block approximately 1/8” (3.2mm) at
release.

Carefully lift and remove port block (2) and port plate (4).

CAUTION:

The port plate may cling to the barrel face because of oil film. Do not allow

the port plate to fall and become damaged.

See figure 6.

Remove the face plate (2) and face plate pins (1) from the face of the

barrel assembly.

See figure 4.1.

Loosen six screws gradually in alternating sequence.

CAUTION:

Holddown is under preload. Do not remove screws completely.

Insert three #10-32 screws into the three #10-32 threaded holes . Alternately  turn in
screws till the tapered retainer releases. A loud crack sound should be heard when it
releases.

See figure 7.

Lock main shaft from turning.

See figure 4.1.

Use special tool 

T2

, slip it over auxiliary shaft (2) and engage dowels

into barrel holddown nut assy. (5). Loosen load but do not remove.

See figure 6.

Remove two bolts (5) holding housing and flange together .

SERVO/REPLENISH PUMP
AND BARREL HOLDDOWN

(continued)

(24 series barrel holddown)

(30 series barrel holddown)

www.comoso.com

Содержание Goldcup 24




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды