Demco HCM Скачать руководство пользователя страница 7

Page 7

AB20020

• 

Do not walk or work under raised components or attachments unless securely positioned and blocked.

• 

Keep all bystanders, pets, and livestock clear of work area.

• 

Operate towing unit from operators seat only.

• 

Never stand alongside of unit with engine running or attempt to start engine and/or operate machine while 

standing alongside of unit.

• 

Never leave running equipment attachments unattended.

• 

As a precaution, always recheck hardware on equipment following every 100 hours of operationCorrect all 

problems. Follow maintenance safety procedures.

SAFETY

DURING OPERATION

• 

Beware of bystanders, 

PARTICulARly ChIldReN!  

Always look around to make sure it is safe to start engine 

of towing unit or move sprayer. This is particularly important with higher noise levels and quiet cabs, as you 

may not hear people shouting. 

 

 

No PAsseNGeRs AlloWed

- Do not carry passengers anywhere on or in the tractor or sprayer. 

• 

Keep hands and clothing clear of moving parts.

• 

Do not clean, lubricate, or adjust your sprayer while it is moving.

• 

When halting operation, even periodically, set tractor or towing unit brakes, disengage PTO, shut off engine, 

and

 remove ignition key

• 

Be especially observant of operating area and terrain- watch for holes, rocks, or other hidden hazards. Always 

inspect area prior to operation. 

 

 

-     DO NOT operate near edge of drop-offs or banks.

 

 

-     DO NOT operate on steep slopes as overturn may result.

 

 

-     Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.

• 

Pick the most level possible route when transporting across fields. Avoid edges of ditches, gullies, and steep 

hillsides.

• 

Be extra careful when working on inclines.

• 

Periodically clear equipment of brush, twigs, or other materials to prevent buildup of dry combustible  materi

-

als. 

• 

Maneuver tractor or towing unit at safe speeds.

• 

Avoid overhead wires or other obstacles. Contact with overhead lines could cause serious injury or death.

• 

Avoid loose gravel, rocks, and holes; they can be dangerous for equipment operation or movement.

• 

Allow for sprayer length when making turns.

Содержание HCM





























Отзывы: