Demco Gravity Flow 550, Руководство пользователя

Страница: 11 / 28

Page 11
RuNNING GeAR PARTs lIsT
INsTAllING The ToNGue ANd
The lIfT AssIsT sPRING
1. Mount the Tongue (H) onto the Pivot Arm (R), fasten together using
one 1-1/2” Dia. x 9” bolt (J) and one 1-1/2” nut (K). Tighten just
enough to take out all slack and hold nut in place using one 1/4” x
1/4” socket set screw (L).
2. Insert 5/8”-11 x 9” bolt through Tongue as shown using two 5/8”
Flatwashers (W), and one 5/8” nylon insert locknut (X). Tighten
bolt until all slack is removed between the tongue and pivot arm
(R). Do not over tighten, the tongue should still move freely. Raise
the tongue and support on a stand.
3. Mount the Lift Assist Plate (Q) onto the top of the Pivot Arm (R) using
two 5/8”-11 x 1-3/4” bolts (S) and two 5/8” nylon insert locknuts
(T).
4. Attach the Lift Assist Springs (M) to the Lift Assist Plate (Q)
by threading the two 1/2”-13 x 6” full thread bolts (N) with 1/2”
lockwasher (O) into the threaded insert in the springs (M). Tighten
the bolts to remove any slack. Remove the stand and adjust the
tongue height using the two 1/2” x 6” bolts.
5. Adjustment of the 5/8” x 2 1/2” bolts (Y) on the Pivot Arm (R) should
be preset to not overturn. If adjustment is required, do so once box
is mounted on running gear. Be careful that tires will not turn into
the box frame.
AdjusTING The TIe Rods foR AlIGNMeNT
1. Alignment is present at the factory. To check alignment, the Tie
Rods (P) should be adjusted to have 1/4” to 3/8” toe in (measured
at tire bead edge of rim). When this adjustment is made, the tongue
must be aligned with the round pipe on the front bolster. Be sure
both wheels toe in equally.
1. Insert the Lock Collar (A) into the opening provided on the Rear
Bolster Pipe Frame (C). The end of the Front Bolster Pipe (B)
should slide into the Rear Bolster Frame (C). Line up the holes in
the Lock Collar and bolt together using one 3/4” x 7” bolt (D) and
one 3/4” nylon locknut (E).
2. Mount the Tire and Rim (F) to the front and rear bolster using forty
3/4” Flanged Wheel Nuts (G) (650 Bu. ). For 550 Bu. mount use
32 5/8” Flanged Wheel Nuts (G). Torque Wheel Nuts to 400 ft*lb
(650 Bu.). For 550 Bu., torque to 225 ft*lb.
TIGHTEN ALL BOLTS (SEE TORQUE CHART ON PAGE 11.)
MouNTING The Wheels, ANd AsseMblING
The fRoNT ANd ReAR bolsTeR fRAMes
AsseMbly INsTRucTIoNs
Ref # PART # qTy descRIPTIoN
1.
07353
1 1-1/4”-12 UNF Castle Nut (650&750)
- 01934 1 1”-14 UNF Castle Nut (550)
2. 05088 1 1/4” x 2” Lg. Cotter Pin (650&750)
- 00191 1 3/16” x 1-1/2” Lg. Cotter Pin (550)
3.
07354
1 1.32” I.D. x 3.00” OD Flatwasher (650&750)
-
01936
1 1-1/16” I.D. x 2-1/8” O.D. Flatwasher (550)
5474-30 4 Wheel Hub Assembly (650 & 750 Bu.)
4. 04305 4 5/16”-18 UNC x 1/2” Hex Head Bolt Gr. 5
5. 07362 1 Hub Cap
6.
07358
1 Outer Cone Bearing (460)
7.
07360
1 Outer Cup (453A)
8. 07435 10 3/4” Flanged Wheel Nut
9. - 1 10 Bolt Hub (W871)
(NOT SOLD SEPARATELY)
- 07861 - 3/4”-16 UNF Stud Bolt (replacement)
10.
07357
1 Inner Cone Bearing (39585)
11.
07359
1 Inner Cup (39520)
12. 07361 1 Oil Seal (CR30087)
13. 09532 1 Gasket
5691-30 4 Wheel Hub Assembly (550 Bu.)
5.
01933
1 Hub Cap
6.
01937
1 Outer Cone Bearing (LM501349)
7. 01938 1 Outer Cup (LM501310)
8. 10971 8 5/8”-18 UNF Wheel Nut, Flanged
9. - 1 8 Bolt Hub (NOT SOLD SEPARATELY)
-
10151
- 5/8”-18 UNF Stud Bolt (replacement)
10.
01942
1 Inner Cone Bearing (JLM506849)
11. 01943 1 Inner Cup (JL506810)
12. 01944 1 Oil Seal (CR27362)
14. 6068-30 2 Tie Rod End w/Left Hand Threads
-
6069-30
2 Tie Rod End w/Right Hand Threads
15.
07324
4 13” Brake Drum (650 & 750 Bu.)
- 03532 2-4 13” Brake Drum (550 Bu.)
(4 whl. brakes optional)
16. 05031 24 1/2”-20UNFx1-1/4” Bolt Gr.5 (550 Qty.32)
17. 02010 16 1/2”-20UNF x 1” Hex Head Bolt Gr. 5
18.
07910
1 Left Brake Cluster (shown)
-
07911
1 Right Brake Cluster (not shown)
19. 07407-30 1 Pivot Arm Mounting Pin
20. 01922 3 1-1/2”-12UNF Hex Nut w/ Set Screw Hole
21. 01923 3 1/4”-20UNC x 1/4” Socket Set Screw
22.
01951
2 1-1/2” I.D. x 1-7/8” O.D. x 2” Bronze Bushing
23.*
6067-30
2 Tie Rod Assembly
24. 09033-30 2 2” Dia. Spindle Mounting Pin
25. 14687-30 1 Right Front Spindle (550 Bu.)
- 07409-30 1 Right Front Spindle (650&750 Bu.)
26.
14686-30
1 Left Front Spindle (550 Bu.)
-
07408-30
1 Left Front Spindle (650&750 Bu.)
27. 14685-30 1 Front Bolster Frame (550&650 Bu.)
- 14326-30 1 Front Bolster Frame (750 Bu.)
28. 01965-30 1 4-1/2” O.D. Collar
29.
01964
1 3/4”-10UNC x 7” Hex Head Bolt Gr. 5
30.
02961
1 3/4”-10UNC Nylon Insert Locknut
31. 13148-30 1 Rear Bolster Frame (550 Bu.)
- 13124-30 1 Rear Bolster Frame (650 Bu.)
- 14327-30 1 Rear Bolster Frame (750 Bu.)
32.
00152
16 1/2”-20 UNF Hex Nut (550 Qty.8)
33.
07356
2 Thrust Bearing
34. 00084 36 1/2” Lockwasher (550 Qty.24)
35. 03908-60 4 22.5 x 13.5 10 Bolt Rim (650/750 Bu. Charcoal)
11291-60 4 22.5 x 13.5 8 Bolt Rim (550 Bu. Charcoal)