Delta RTU-ECAT Скачать руководство пользователя страница 75

Страница: 75 / 79

RTU-ECAT Operation Manual

8-2

RTU-ECAT provides two diagnostic methods, LED indicator diagnosis and status indication diagnosis.

8.1

LED Indicator Diagnosis

POWER LED

LED status

Indication

How to correct

Off

Power is abnormal.

Make sure that RTU-ECAT is powered.

Green light on Power is normal.

ALARM

LED

LED status

Indication

How to correct

Off

RTU-ECAT works normally or
lacks the work power.

Red light

blinking

Possible causes:

1. The configuration data of

RTU-ECAT are invalid;

2. The extension modules on

the right of RTU-ECAT are in
error or are offline.

1. Check if the modules on the right of RTU-ECAT

are consistent with those configured in the
software.

2. Check out the error information of the modules on

the right of RTU-ECAT and then deal with the
errors by following related module manual
instructions.

3. Check if the power supply and wiring of the

modules on the right of RTU-ECAT are fine.

4. Make sure that the wiring of EtherCAT cables is

proper.

Red light on RTU-ECAT is under voltage

Check if the power supply for RTU-ECAT is normal.

RUN LED

LED status

Indication

How to correct

Off

RTU-ECAT in STOP mode

1. Ensure that the power supply for RTU-ECAT and

the connection are fine.

2. Check if the RUN/STOP switch of RTU-ECAT has

been switched to RUN.

3. Check if the control word of RTU-ECAT is effective

and controlling RTU-ECAT in STOP state.

Green light on RTU-ECAT in RUN mode

Содержание RTU-ECAT
















































































Результаты поиска

Содержание RTU-ECAT

Отзывы:

Похожие инструкции для RTU-ECAT

Бренды по названию

Популярные бренды

Delta RTU-ECAT, Руководство по эксплуатации

Результаты поиска

Содержание RTU-ECAT

Отзывы:

Похожие инструкции для RTU-ECAT

Бренды по названию

Популярные бренды