background image

 

Input Sensor Type 

Display 

Temperature Range 

0V ~ 5V input 

 

-999 ~ 9,999 

0 ~ 70mV input 

 

-999 ~ 9,999 

Cu50 type 

 

-50

 o

C ~ 150

 o

C (-90.0

 o

F ~ 302.0

 o

F) 

Pt100 type 2 

 

-99.9

o

C ~ 600.0

o

C (-99.9

o

F ~ 999.9

o

F) 

Pt100 type 1 

 

-200

o

C ~ 600

o

C (-360

o

F ~ 1,112

o

F) 

JPt100 type 

 

-20.0

o

C ~ 400.0

o

C (-36.0

o

F ~ 752.0

o

F) 

Thermocouple TXK type 

 

-200

o

C ~ 800

o

C (-360

o

F ~ 1,472

o

F) 

Thermocouple U type 

 

-200

o

C ~ 500

o

C (-360

o

F ~ 932

o

F) 

Thermocouple L type 

 

-200

o

C ~ 850

o

C (-360

o

F ~ 1,562

o

F) 

Thermocouple B type 

 

100

o

C ~ 1,800

o

C (180

o

F ~ 3,272

o

F) 

Thermocouple S type 

 

0

o

C ~ 1,700

o

C (0

o

F ~ 3,092

o

F) 

Thermocouple R type 

 

0

o

C ~ 1,700

o

C (0

o

F ~ 3,092

o

F) 

Thermocouple N type 

 

-200

o

C ~ 1,300

o

C (-360

o

F ~ 2,372

o

F) 

Thermocouple E type 

 

0

o

C ~ 600

o

C (0

o

F ~ 1,112

o

F) 

Thermocouple T type 2 

 

-99.9

o

C ~ 400.0

o

C (-99.9

o

F ~ 752.0

o

F) 

Thermocouple T type 1 

 

-200

o

C ~ 400

o

C (-360

o

F ~ 752

o

F) 

Thermocouple J type 2 

 

-99.9

o

C ~ 999.9

o

C (-99.9

o

F ~ 999.9

o

F) 

Thermocouple J type 1 

 

-200

o

C ~ 1,200

o

C (-360

o

F ~ 2,192

o

F) 

Thermocouple K type 2 

 

-99.9

o

C ~ 999.9

o

C (-99.9

o

F ~ 999.9

o

F) 

Thermocouple K type 1 

 

-200

 o

C ~ 1,300

o

C (-360

o

F ~ 2,372

o

F) 

 

Control Settings

!

 

Setting up Control Mode

 

In the operation mode, press 

  for more than 3 seconds and PV will display the parameter 

. Press 

  for 4 times to display 

the parameter 

. The default setting of this parameter is “On/Off control” 

. Use 

  to select PID control 

, PID 

programmable control 

  or manual control 

. Press 

  again and display the parameter 

  for selecting the control 

method. You can select heading (default) 

 or cooling 

. Press 

  to return to the operation mode. 

 

Setting up RUN and STOP 

 

In the operation mode, press 

 and display parameter 

. The default is RUN 

. Use 

  to select STOP 

. Press 

  to complete the setting and the output will be disabled. 

 

Setting up On/Off Control Parameters

 

Press 

  in the operation mode. If DTD is in On/Off heating mode, the PV will display 

; if in On/Off cooling mode, the PV will 

display 

. Modify these parameters to set up the hysteresis of On/Off. The default setting is 0 (without hysteresis). When the output 

reaches SV, the control output will be disabled. When the input is bigger (cooling) or smaller (heating) than the SV and hysteresis, the 
control output will be enabled. When the On/Off hysteresis is not 0, the control output will be like the diagrams below. 

 

 

Hysteresis

HtS

OFF

ON

OFF

ON/OFF Control for Heating

SV

     

Hysteresis

CtS

OFF

ON

ON

ON/OFF Control for Cooling

SV

 

 

 

Setting up PID Parameters

 

When in PID control mode, you have to first decide the On/Off cycle time for the control output, i.e. the control cycle. Press 

 in the 

operation mode and PV will display 

. Press 

  5 times to display the parameters of heating control cycle 

 or cooling 

control cycle 

. Set up the cycle depending on the reaction speed of the control system. In principle, the faster the reaction, the 

shorter the cycle and more accurate the control. A short control cycle indicates that there will be more times of On/Off. If you adopt relay 
output, the short cycle will shorten the life span of the relay. Therefore, it is recommended that you adopt voltage output in the PID control 
mode. The default setting of the control cycle is 20 seconds.   

 

3

Содержание DTD Series








Отзывы: