(4) Dimensions for Installation
DOP-103WQ
Operation Temperature is 0
o
C to 50
o
C and Storage Temperature is -20
o
C to +60
o
C
DOP-107WV
Operation Temperature is 0
o
C to 50
o
C and Storage Temperature is -20
o
C to +60
o
C
DOP-110WS
Operation Temperature is 0
o
C to 50
o
C and Storage Temperature is -20
o
C to +60
o
C
(5) Installation and Wiring
Installation Notes:
Improper installation will result in malfunction and greatly reduce the life of the HMI. Be sure to
follow the guidelines in this quick start when installing the HMI.
In order to ensure the HMI being well ventilated, make sure that the ventilation holes are not
obstructed and provide sufficient clearance for the HMI.
To protect the panel, be sure to install a waterproof gasket into HMI.
For use on a flat surface of a Type 4X "Indoor Use Only" enclosure or equivalent. If Enclosure with
lower type rating will cause de-rating.
The allowable thickness of the panel for mounting should be less than 5 mm.
Installation Method:
Step 1:
Put the waterproof gasket into HMI and then
insert the HMI into the panel cutout.
Step 2:
Place the fasteners into slots and tighten the
screws till reaching the panel cutouts.
Step 3:
Tighten the screws with torque less than 0.5N-M /
0.7N-M to avoid damage to the plastic case.
DOP-107/DOP-110 Torque: 6.17 lb-inch (0.7N-M)
DOP-103 Torque: 4.41 lb-inch
（
0.5N-M
）
Step 4:
For heat dissipation, please keep a minimum
clearance of 60 mm on the rear of the HMI.
Recommended wiring is as follows:
Type
Wire Gauge (AWG)
Stripped length
Torque
Solid
24 ~ 12
7 ~ 8 mm
5 kg-cm (4.3 lb-in)
Stranded
24 ~ 12
7 ~ 8 mm
5 kg-cm (4.3 lb-in)
Be sure to perform wiring by referring to the following figure (power supply connector), wiring must
be rated 75
℃
min.
(6) Specifications
Model
DOP-103WQ
DOP-107WV
DOP-110WS
LCD
Module
Display Type
4.3" TFT LCD
（
65535 colors
）
7" TFT LCD
(65535 colors)
10.1" TFT LCD
(65535 colors)
Resolution
480 x 272 pixels
800 x 480 pixels
1024 x 600 pixels
Backlight
LED Back Light (less than
10,000 hours half-life at
25
o
C)
(Note 1)
LED Back Light (less than
20,000 hours half-life at
25
o
C)
(Note 1)
LED Back Light (less than
30,000 hours half-life at 25
o
C)
(Note 1)
Display Size
95.04 x 53.856 mm
154.08 x 85.92 mm
225.52 x 128.10 mm
Brightness
400 cd/m² (Typ.)
450 cd/m² (Typ.)
450 cd/m² (Typ.)
CPU
ARM Cortex-A8 (800MHz)
Model
DOP-103WQ
DOP-107WV
DOP-110WS
Flash ROM
256 Mbytes
RAM
512 Mbytes
Touch Screen
4-wire resistive touch screen
> 10,000,000 operated
Buzzer
Multi-Tone Frequency (2 K ~ 4 K Hz)
／
80 dB
Ethernet Interface
10/100 Mbps Auto sensing (with built-in isolated power circuit
(Note 2)
)
USB
1 USB Slave Ver 2.0
1 USB Host Ver 2.0
SD
N/A
SD * 1
Serial
Communication
Port
COM1
RS-232 (supports flow
control) / RS-485
(Note 2)
)
RS-232 (supports flow control)
(Note 2)
)
COM2
RS-422 / RS-485
(Note 2)
RS-232 (supports flow control) / RS-485
(Note 2)
)
COM3
N/A
RS-422 / RS-485
(Note 2)
)
Function Keys
N/A
Perpetual Calendar
Built-in
Cooling Method
Natural cooling
Safety Approval
CE / UL (Please use shielding Ethernet cable and the magnetic ring with filter of
300 ohm/100 MHz)
Waterproof Level of
Panel Display
IP65(Not be evaluated by UL)/NEMA4/ Type 4X indoor use only
Operation Voltage
(Note2)
+24 V
DC
(-15% ~ +15%) (with built-in isolated power supply unit)
Supplied by Class 2 or SELV circuit (isolated from MAINS by double insulation)
Voltage Endurance
500 V
AC
for 1 minute (between charging (DC24V terminal) and FG terminals)
Power Consumption
(Note
2)
5.8W (Max)
(Note 3)
8.4W (Max)
(Note 3)
11W (Max)
(Note 3)
Backup Battery
3V lithium battery CR2032 × 1
Backup Battery Life
About 3 years or more at 25
o
C but subjects to the temperature and the conditions
during usage.
Operation Temperature
0
o
C ~ 50
o
C
Storage Temperature
-20
o
C ~ +60
o
C
Operating Environment
10% ~ 90% RH [0 ~ 40
o
C], 10% ~ 55% RH [41 ~ 50
o
C]; Pollution degree: 2
Vibration Resistance Conforms to IEC61131-2; Continuous: 5 Hz ~ 8.3 Hz 3.5 mm, 8.3 Hz ~ 150 Hz 1 G
Shock Resistance
Conforms to IEC60068-2-27: 11 ms, 15 G Peak , X, Y, Z direction for 6 times
Dimension
(W) x (H) x (D) mm
137 x 103 x 37.1
196 x 136 x 39
270 x 180.9 x 47.25
Dimension for
Installation
(W) x (H) mm
118.8 x 92.8
186.8 x 126.8
255 x 170
Weight
Approx.280g
Approx. 560 g
Approx. 1.1 Kgs
Note:
1. The half-life of backlight is defined as original luminance being reduced by 50% when the maximum
driving current is supplied to HMI. The life of LED backlight shown here is an estimated value under 25
o
C
normal temperature and humidity conditions.
2. The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute.
3. Power consumption of HMI is the power consumed when not connecting to any peripheral devices. To
ensure normal operation of HMI, the recommended power supply is: power consumption x 1.5 ~ 2.
4. Isolated power supply is recommended.
5. DOPSoft, the program editor for DOP-100 series products and user manuals can be downloaded at
our website. In addition, the content of this instruction sheet may be revised without prior notice.
Please consult our distributors or download the latest version at http://www.delta.com.tw/ia.
6. DOP-100 series can be used for industrial automation equipment. Please read through this manual
carefully and install the product according to the instructions to avoid danger.
