manualshive.com logo in svg

Delta CMM-EC02, Руководство по эксплуатации, Страница: 29 / 64

Поделиться
Скачать
Delta CMM-EC02 Скачать руководство пользователя страница 29

6.2  SDO Abort Code 

 

SDO Abort Code 

Description 

0x05030000 

Deflection fault while doing segment transmission   

0x05040000 

SDO time out.   

0x05040001 

Client / servo command are invalid or don’t exist. 

0x05040005 

Register overflow when running SDO. 

0x06010000 

Not supported access 

0x06010001 

Try to read a write-only object 

0x06010002 

Try to write a read-only object 

0x06010003 

Unable to write into sub-index. The sub-index has to be 0. 

0x06020000 

The object doesn’t exist in the object dictionary. 

0x06040041 

Unable to map the object to PDO 

0x06040042 

The number and the length of the objects mapped to PDO is longer than PDO. 

0x06040043 

Format of the parameter is not compatible. 

0x06040047 

Compatibility issue of motor drive. 

0x06060000 

Fail to save due to hardware error. (Saving or returning to origin fault) 

0x06070010 

Incorrect data type; wrong parameter length. 

0x06070012 

Incorrect data type; parameter length is too long 

0x06070013 

Incorrect data type; parameter length is too short. 

0x06090011 

Sub-index doesn’t exist. 

0x06090030 

The parameter value is out of bounds.   

0x06090031 

Setting value is too big. 

0x06090032 

Setting value is too small. 

0x06090033 

Detected Module Ident List (0xF030) and Configured Module Ident list (0xF050) don’t 

match. 

0x06090036 

Setting value is smaller than the lower limit. 

0x08000000 

General error 

0x08000020 

Data cannot be read or written. 

0x08000021 

Data access denied due to local control. 

0x08000022 

Data access denied due to current status. 

0x08000023 

Object dictionary doesn’t exist. 

 
 
 
 

 

Send Quote Requests to info@automatedpt.com

Call +1(800)985-6929 To Order or Order Online At Deltaacdrives.com

Send Quote Requests to info@automatedpt.com 

Call +1(800)985-6929 To Order or Order Online At Deltaacdrives.com

Содержание CMM-EC02

































































Отзывы:

Нет отзывов